- Subscribe to RSS Feed
- Mark as New
- Mark as Read
- Bookmark
- Subscribe
- Printer Friendly Page
- Report Inappropriate Content
on 04-10-2018 03:03 AM
- Introduction
- Pre-requisite:
- Caveat :
- When IPXE Boot could be done :
- IPXE Boot :
- Ipxe boot using DHCP Server :
Introduction
iPXE boot in ASR9K
Migration recommendation document for Cxr to Exr.
Pre-requisite:
- Needed only IOS XR 64-bit ISO image.
Example : “asr9k-mini-x64-6.2.3.iso”
Caveat :
Config will be lost we needed to save the configuration in advance before migration on external server.
This can be done only on a RSP880 , RP2 and above .
Disk and hard disk would be formatted while migration we needed to save the configuration and relevant logs externally .
When IPXE Boot could be done :
-
During migration from C-xr to E-xr (only using migration script )
-
Password recovery
-
When router boot up fails with E-xr .
-
During Downgrade from 6225 and below we needed to do Ipxe boot
IPXE Boot :
iPXE is a pre-boot execution environment that is embedded in the router and works at the BIOS level. iPXE is used to re-image the system, boot the router in case of boot failure or in the absence of a valid bootable partition.
Summary of Steps:
- Before your use the iPXE boot, ensure that config backup is taken in advance to a tftp/ftp path to load the config back after the ipxe boot .
- Login to the System Admin console using the admin command.
- If router is unable to boot then intiate an OIR of both RP (Active and Standby RP)
- After aborting the boot process. you get the following options to boot as mentioned below and choose the option 4 for IPXE boot
- After option 4 is selected please press CTRL+b as soon as you see this syslog on the router “Selected external PXE “to enter to IPXE prompt <IPXE>
- Manually update IPXE Rommon details before booting via FTP/TFTP:
- ENTER THE NEW PASSWORD as prompted
- Standby RP will Sync with active RP once active RP is booted successfully .
- If standby RP is not getting sync then press ctrl +C and select option 5 from boot.
Steps in details
Step 1: Before your use the iPXE boot, ensure that config backup is taken in advance to a tftp/ftp path to load the config back after the ipxe boot .
Step 2: Login to the System Admin console using the admin command.
The following example shows the output of the command:
sysadmin-vm:0_RSP0# hw-module location all reload
Tue Mar 6 08:12:47.605 UTC
Reload hardware module ? [no,yes] yes
result Card graceful reload request on all acknowledged.
sysadmin-vm:0_RSP0#
Step 3 : If router is unable to boot then intiate an OIR of both RP (Active and Standby RP)
Press Ctrl +C as soon as you see this below log -
##########################################################
System Bootstrap, Version 10.57 [ASR9K x86 ROMMON],
Copyright (c) 1994-2014 by Cisco Systems, Inc.
Compiled on Mon 01/09/2017 17:15:01.98
BOARD_TYPE : 0x100317
Rommon : 10.57 (Primary)
Board Revision : 4
PCH EEPROM : 3.4
IPU FPGA(PL) : 0.40.0 (Backup)
IPU INIT(HW_FPD) : 0.30.0
IPU FSBL(BOOT.BIN) : 1.19.0
IPU LINUX(IMAGE.FPD) : 1.21.0
OPTIMUS FPGA : 0.12.0
OMEGA FPGA : 0.13.0
ALPHA FPGA : 0.14.0
CHA FPGA : 0.5.1
CBC0 : Part 1=34.38, Part 2=34.38, Act Part=2
Product Number : A9K-RSP880-SE
Chassis : ASR-9904-AC
Chassis Serial Number : FOX1936GBDD
Slot Number : 1
Pxe Mac Address LAN 0 : 70:e4:22:06:13:40
Pxe Mac Address LAN 1 : 70:e4:22:06:13:41
==========================================================
Got EMT Mode as 3
Got Boot Mode as 0
Booting IOS-XR (32 bit Classic XR) - Press Ctrl-c to stop
Step 4 : After aborting the boot process. you get the following options to boot as mentioned below and choose the option 4 for IPXE boot :
Please select the operating system and the boot device:
1) IOS-XR (32 bit Classic XR)
2) IOS-XR 64 bit Boot previously installed image
3) IOS-XR 64 bit Mgmt Network boot using DHCP server
4) IOS-XR 64 bit Mgmt Network boot using local settings (iPXE)
5) IOS-XR 64 bit Internal network boot from RSP/RP
6) IOS-XR 64 bit Local boot using embedded USB media
7) IOS-XR 64 bit Local boot using front panel USB media
Selection [1/2/3/4/5/6/7]:
Step 5 : After option 4 is selected please press CTRL+b as soon as you see this syslog on the router “Selected external PXE “to enter to IPXE prompt <IPXE>
The following logs for reference: -
Please select the operating system and the boot device:
1) IOS-XR (32 bit Classic XR)
2) IOS-XR 64 bit Boot previously installed image
3) IOS-XR 64 bit Mgmt Network boot using DHCP server
4) IOS-XR 64 bit Mgmt Network boot using local settings (iPXE)
(Press 'p' for more option)
Selection [1/2/3/4]: 4
Selected IOS-XR 64 bit Mgmt Network boot using local settings (iPXE), Continue ? Y/N: y
Serial ATA Port 4 : SMART iSATA SHSLM32GEBCITHD0
Serial ATA Port 5 : SMART iSATA SHSLM32GEBCITHD0
USB Device 1 : STEC STEC USB 2.0
Selected external PXE
Since response is not received for os_type, switch to IOS-XR 32 bit
CISCO iPXEiPXE initialising devices...ok
iPXE 1.0.0+ (f6488) -- Open Source Network Boot Firmware -- http://ipxe.org
Features: DNS HTTP TFTP EFI ISO9660 Menu
IPXE embed script.......
IPXE preference ...1
Using rommon variables....
ROMMON SETTINGS
...............
cisco/cisco-ipv4-address:string = 5.34.16.100
cisco/cisco-netmask-address:str = 255.255.0.0
cisco/cisco-gateway-address:str = 5.34.0.1
Err: cisco-server-url not set
cisco/cisco-server-url:string =
===============================================================================
NETWORK SETTINGS
................
net0/ip:ipv4 = 5.34.16.100
net0/gateway:ipv4 = 5.34.0.1
net0/netmask:ipv4 = 255.255.0.0
net0/mac:hex = 70:e4:22:06:13:40
net1/ip:ipv4 = 5.34.16.100
net1/gateway:ipv4 = 5.34.0.1
net1/netmask:ipv4 = 255.255.0.0
net1/mac:hex = 70:e4:22:06:13:41
..................
Press Ctrl-B for the iPXE command line...
Opening net0, close net1...
iPXE>
Step 6 : Manually update IPXE Rommon details before booting via FTP/TFTP:
Set below variables in iPXE prompt if Rommon variables are not set.
iPXE>cisco/cisco-server-url:string=tftp://YOURSERVER_IP/auto/tftpboot-SMU/612/ASR9K/asr9k-mini-x64.iso
iPXE>cisco/cisco-ipv4-address:string=1.3.24.202
iPXE>cisco/cisco-netmask-address:str=255.255.0.0
iPXE>cisco/cisco-gateway-address:str=1.3.0.1
Note: where net0 represents mgmt port0 and net1 represents mgmt port1 :
now open the connected mgmt port (0/1) with this Command “ifopen net0/1 “ then boot the require image from tftp location or reachability.
And next open the front ports and execute the boot command in ipXE prompt
iPXE>ifclose net0
iPXE>ifclose net1
iPXE>ifopen net 1
iPXE>boot tftp://YOURSERVER_IP/file path/image.iso
The following example for reference for 623 image.
iPXE>
iPXE> ifopen net0:
iPXE> boot tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso
tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso... 0%
iPXE>
iPXE>
iPXE> boot tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso
tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso... 15%
iPXE>
iPXE> boot tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso
tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso... 74%
Memory required for image[asr9k-mini-x64-6.2.3.iso]: 1135456256, available: 1841299456
Booting iso-image@0x83c525000(1135456256), bzImage@0x83c55f000(4526671)
.......BIOS CODE SIGN ENTRY ...
!!!! IPXE boot syslogs logs !!!
Serial ATA Port 4 : SMART iSATA SHSLM32GEBCITHD02
Serial ATA Port 5 : SMART iSATA SHSLM32GEBCITHD02
Selected external PXE
CISCO iPXEiPXE initialising devices...ok
iPXE 1.0.0+ (f6488) -- Open Source Network Boot Firmware -- http://ipxe.org
Features: DNS HTTP TFTP EFI ISO9660 Menu
IPXE embed script.......
IPXE preference ...1
Using rommon variables....
ROMMON SETTINGS
...............
cisco/cisco-ipv4-address:string = 5.32.23.5
cisco/cisco-netmask-address:str = 255.255.0.0
cisco/cisco-gateway-address:str = 5.32.0.1
Err: cisco-server-url not set
cisco/cisco-server-url:string =
===============================================================================
NETWORK SETTINGS
................
net0/ip:ipv4 = 5.32.23.5
net0/gateway:ipv4 = 5.32.0.1
net0/netmask:ipv4 = 255.255.0.0
net0/mac:hex = d4:6d:50:64:74:e0
net1/ip:ipv4 = 5.32.23.5
net1/gateway:ipv4 = 5.32.0.1
net1/netmask:ipv4 = 255.255.0.0
net1/mac:hex = d4:6d:50:64:74:e1
..................
Press Ctrl-B for the iPXE command line...
iPXE>
iPXE>
iPXE>
iPXE> boot tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso
tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso... 0%
iPXE>
iPXE>
iPXE> boot tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso
tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso... 15%
iPXE>
iPXE> boot tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso
tftp://202.153.144.25/auto/tftpboot-SMU/623/ASR9K-XR/asr9k-mini-x64-6.2.3.iso... 74%
Memory required for image[asr9k-mini-x64-6.2.3.iso]: 1135456256, available: 1841299456
Booting iso-image@0x83c525000(1135456256), bzImage@0x83c55f000(4526671)
.......BIOS CODE SIGN ENTRY ...
Image ASR9K-Tomahawk verified successfully
**** PASS: secure boot verification of image: bzImage****
[output omitted]
Step 7 : ENTER THE NEW PASSWORD as prompted
!!!!!!!!!!!!!!!!!!!! NO root-system username is configured. Need to configure root-system username. !!!!!!!!!!!!!!!!!!!!
--- Administrative User Dialog ---
Enter root-system username: lab
Enter secret:
Use the 'configure' command to modify this configuration.
User Access Verification
Username:
!!!! ADMIN PROMPT syslogs !!!
Press RETURN to get started.
0/RSP0/ADMIN0:Mar 6 08:34:00.050 : vm_manager[3773]: %INFRA-VM_MANAGER-4-INFO : Info: vm_manager started VM default-sdr--1
0/RSP0/ADMIN0:Mar 6 08:34:41.933 : shelf_mgr[3761]: %INFRA-SHELF_MGR-4-CARD_RELOAD : Reloading card 0/1
0/1/ADMIN0:Mar 6 08:34:58.489 : inst_agent[3189]: %INFRA-INSTAGENT-2-SELF_TEST_FAILED : This node has failed verification of its installed software base. A new disk will be prepared.
0/RSP0/ADMIN0:Mar 6 08:36:55.208 : esdma[4962]: %PKT_INFRA-FM-4-FAULT_MINOR : ALARM_MINOR :ESDMA lost connectivity with ESD :DECLARE :0/LC1/LC_SW:
RP/0/RSP0/CPU0:ios#sh plat
Tue Mar 6 09:24:09.083 UTC
Node Type State Config state
--------------------------------------------------------------------------------
0/RSP0/CPU0 A9K-RSP880-SE(Active) IOS XR RUN NSHUT
0/RSP1/CPU0 A9K-RSP880-SE(Standby) IOS XR RUN NSHUT
0/FT0 ASR-9904-FAN OPERATIONAL NSHUT
0/1/CPU0 A9K-4X100GE-TR IOS XR RUN NSHUT
0/PT0 A9K-AC-PEM-V2 OPERATIONAL NSHUT
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#sh install active summary
Tue Mar 6 09:24:12.488 UTC
Active Packages: 1
asr9k-xr-6.2.3 version=6.2.3 [Boot image]
RP/0/RSP0/CPU0:ios#
System Admin Username: lab
Password:
lab connected from 127.0.0.1 using console on sysadmin-vm:0_RSP0
sysadmin-vm:0_RSP0#
sysadmin-vm:0_RSP0#
sysadmin-vm:0_RSP0#
Step 8: Standby RP will Sync with active RP once active RP is booted successfully .
!!! Sys logs from standby console reference !!!
This (D)RP Node is not ready or active for login /configuration
Usage
hushd_platform.sh update_flash
boardtype flash_type : Update boardtype in flash
hushd_platform.sh get_bios_ver
boardtype flash_type : Get BIOS version from flash
Stopping
Stopping OpenBSD Secure Shell server: sshdinitctl: Unknown instance:
Stopping system message bus: dbus.
Stopping libvirtd daemon: [ OK ]
Stopping system log daemon...0
Stopping kernel log daemon...0
Stopping internet superserver: xinetd.
Stopping crond: OK
Stopping rpcbind daemon...
done.
Stopping S.M.A.R.T. daemon: smartd.
Stopping Lighttpd Web Server: stopped /usr/sbin/lighttpd (pid 3692)
lighttpd.
Deconfiguring network interfaces... done.
Sending all processes the KILL signal...
umount: /dev/mq: mountpoint not found
Tue Mar 6 08:13:04 UTC 2018: halt -w
Tue Mar 6 08:13:04 UTC 2018: Reboot Mode: 2, Hushd mode: 6, IPU: 20
Unmounting remote filesystems...
Deactivating swap...
Unmounting local filesystems...
mount: / is busy
Tue Mar 6 08:13:24 UTC 2018: halt -d -f -h
get_ipu_base: pci_attach failed
Tue Mar 6 08:13:24 UTC 2018: Reboot Mode: 2, Hushd mode: 6, IPU: 20
��Booting Main Processor
Transferring Console
[=3h[=3h[=3h��) ��)
CPU reset reason = 5 (CPU_RESET_POR)
##########################################################
System Bootstrap, Version 10.58 [ASR9K x86 ROMMON],
Copyright (c) 1994-2014 by Cisco Systems, Inc.
Compiled on Wed 01/25/2017 10:48:20.82
BOARD_TYPE : 0x100317
Rommon : 10.58 (Primary)
Board Revision : 4
PCH EEPROM : 3.4
IPU FPGA(PL) : 0.47.0 (Primary)
IPU INIT(HW_FPD) : 0.57.0
IPU FSBL(BOOT.BIN) : 1.103.0
IPU LINUX(IMAGE.FPD) : 1.103.0
OPTIMUS FPGA : 0.12.0
OMEGA FPGA : 0.16.0
ALPHA FPGA : 0.16.0
CHA FPGA : 0.6.1
CBC0 : Part 1=34.38, Part 2=34.38, Act Part=2
Product Number : A9K-RSP880-SE
Chassis : ASR-9904-AC
Chassis Serial Number : FOX1839H3NF
Slot Number : 2
Pxe Mac Address LAN 0 : 70:e4:22:06:13:40
Pxe Mac Address LAN 1 : 70:e4:22:06:13:41
==========================================================
Got EMT Mode as 2
Got Boot Mode as 0
Booting IOS-XR 64 bit Boot previously installed image - Press Ctrl-c to stop
Step 9 : If standby RP is not getting sync then press ctrl +C and select option 5 from boot.
Please select the operating system and the boot device:
1) IOS-XR (32 bit Classic XR)
2) IOS-XR 64 bit Boot previously installed image
3) IOS-XR 64 bit Mgmt Network boot using DHCP server
4) IOS-XR 64 bit Mgmt Network boot using local settings (iPXE)
(Press 'p' for more option)
Selection [1/2/3/4]:
Please select the operating system and the boot device:
1) IOS-XR (32 bit Classic XR)
2) IOS-XR 64 bit Boot previously installed image
3) IOS-XR 64 bit Mgmt Network boot using DHCP server
4) IOS-XR 64 bit Mgmt Network boot using local settings (iPXE)
(Press 'p' for more option)
Selection [1/2/3/4]: �Booting Main Processor
Transferring Console
Transferring Console
�[=3h[=3h[=3h����^�
CPU reset reason = 8 (CPU_RESET_WDOG_POR)
##########################################################
System Bootstrap, Version 10.58 [ASR9K x86 ROMMON],
Copyright (c) 1994-2014 by Cisco Systems, Inc.
Compiled on Wed 01/25/2017 10:48:20.82
BOARD_TYPE : 0x100317
Rommon : 10.58 (Primary)
Board Revision : 4
PCH EEPROM : 3.4
IPU FPGA(PL) : 0.47.0 (Primary)
IPU INIT(HW_FPD) : 0.57.0
IPU FSBL(BOOT.BIN) : 1.103.0
IPU LINUX(IMAGE.FPD) : 1.103.0
OPTIMUS FPGA : 0.12.0
OMEGA FPGA : 0.16.0
ALPHA FPGA : 0.16.0
CHA FPGA : 0.6.1
CBC0 : Part 1=34.38, Part 2=34.38, Act Part=2
Product Number : A9K-RSP880-SE
Chassis : ASR-9904-AC
Chassis Serial Number : FOX1839H3NF
Slot Number : 2
Pxe Mac Address LAN 0 : 70:e4:22:06:13:40
Pxe Mac Address LAN 1 : 70:e4:22:06:13:41
==========================================================
Got EMT Mode as 2
Got Boot Mode as 0
Booting IOS-XR 64 bit Boot previously installed image - Press Ctrl-c to stop
Checking peer OS type.
Serial ATA Port 4 : SMART iSATA SHSLM32GEBCITHD0
Serial ATA Port 5 : SMART iSATA SHSLM32GEBCITHD0ASR9K Host OS.......BIOS CODE SIGN ENTRY ...
Image ASR9K-Tomahawk verified successfully
Image Verification Passed
[output Omittted]
ios con0/RSP1/CPU0 is in standby
Once active has booted up, select option 5 from boot menu on standby to boot from active RP/RSP if not sync .
!!!! SYS Admin !!!!
Press RETURN to get started.
0/RSP0/ADMIN0:Mar 6 08:56:21.602 : shelf_mgr[3761]: %INFRA-SHELF_MGR-4-CARD_RELOAD : Reloading card 0/RSP1
0/RSP0/ADMIN0:Mar 6 08:57:11.207 : esdma[4962]: %PKT_INFRA-FM-4-FAULT_MINOR : ALARM_MINOR :ESDMA lost connectivity with ESD :DECLARE :0/RP1/RP_SW:
0/1/ADMIN0:Mar 6 09:00:01.743 : vm_manager[3572]: %INFRA-VM_MANAGER-4-INFO : Info: vm_manager started VM default-sdr--1
0/RSP0/ADMIN0:Mar 6 09:09:44.511 : esdma[4962]: %PKT_INFRA-FM-4-FAULT_MINOR : ALARM_MINOR :ESDMA lost connectivity with ESD :CLEAR :?/RP1/RP_SW:
0/RSP1/ADMIN0:Mar 6 09:09:57.495 : sdr_mgr[3962]: %SM-SDR_MANAGER-4-INFO : Info: SDR-RM Standby Initialized
0/RSP1/ADMIN0:Mar 6 09:09:57.509 : pm[3770]: %INFRA-Process_Manager-3-PROCESS_RESTART : Process led_mgr (IID: 0) restarted
0/RSP1/ADMIN0:Mar 6 09:09:57.550 : sdr_mgr[3962]: %SM-SDR_MANAGER-4-INFO : Info: SDR-SM Standby Initialized
0/RSP1/ADMIN0:Mar 6 09:12:31.405 : vm_manager[3977]: %INFRA-VM_MANAGER-4-INFO : Info: vm_manager started VM default-sdr--1
System Admin Username: lab
Password:
lab connected from 127.0.0.1 using console on sysadmin-vm:0_RSP0
sysadmin-vm:0_RSP0# sh plat
Tue Mar 6 09:23:27.624 UTC
Location Card Type HW State SW State Config State
----------------------------------------------------------------------------
0/1 A9K-4X100GE-TR OPERATIONAL OPERATIONAL NSHUT
0/RSP0 A9K-RSP880-SE OPERATIONAL OPERATIONAL NSHUT
0/RSP1 A9K-RSP880-SE OPERATIONAL OPERATIONAL NSHUT
0/FT0 ASR-9904-FAN OPERATIONAL N/A NSHUT
0/PT0 A9K-AC-PEM-V2 OPERATIONAL N/A NSHUT
sysadmin-vm:0_RSP0#
!!! XR Promp !!!!
ios con0/RSP0/CPU0 is now available
Press RETURN to get started.
0/RSP0/ADMIN0:Mar 6 08:56:21.602 : shelf_mgr[3761]: %INFRA-SHELF_MGR-4-CARD_RELOAD : Reloading card 0/RSP1
0/RSP0/ADMIN0:Mar 6 08:57:11.207 : esdma[4962]: %PKT_INFRA-FM-4-FAULT_MINOR : ALARM_MINOR :ESDMA lost connectivity with ESD :DECLARE :0/RP1/RP_SW:
0/1/ADMIN0:Mar 6 09:00:01.743 : vm_manager[3572]: %INFRA-VM_MANAGER-4-INFO : Info: vm_manager started VM default-sdr--1
0/RSP0/ADMIN0:Mar 6 09:09:44.511 : esdma[4962]: %PKT_INFRA-FM-4-FAULT_MINOR : ALARM_MINOR :ESDMA lost connectivity with ESD :CLEAR :?/RP1/RP_SW:
RP/0/RSP0/CPU0:Mar 6 09:09:49.764 : fpd-serv[157]: %PKT_INFRA-FM-3-FAULT_MAJOR : ALARM_MAJOR :FPD-NEED-UPGRADE :DECLARE :0/RSP1:
0/RSP1/ADMIN0:Mar 6 09:09:57.495 : sdr_mgr[3962]: %SM-SDR_MANAGER-4-INFO : Info: SDR-RM Standby Initialized
0/RSP1/ADMIN0:Mar 6 09:09:57.509 : pm[3770]: %INFRA-Process_Manager-3-PROCESS_RESTART : Process led_mgr (IID: 0) restarted
0/RSP1/ADMIN0:Mar 6 09:09:57.550 : sdr_mgr[3962]: %SM-SDR_MANAGER-4-INFO : Info: SDR-SM Standby Initialized
0/RSP1/ADMIN0:Mar 6 09:12:31.405 : vm_manager[3977]: %INFRA-VM_MANAGER-4-INFO : Info: vm_manager started VM default-sdr--1
RP/0/RSP0/CPU0:Mar 6 09:13:21.991 : rmf_svr[142]: %PKT_INFRA-FM-2-FAULT_CRITICAL : ALARM_CRITICAL :RP-RED-LOST-PNP :CLEAR :0:
RP/0/RSP0/CPU0:Mar 6 09:14:11.905 : rmf_svr[142]: %PKT_INFRA-FM-3-FAULT_MAJOR : ALARM_MAJOR :RP-RED-LOST-NSRNR :CLEAR :0:
RP/0/RSP0/CPU0:Mar 6 09:14:58.672 : rmf_svr[142]: %HA-REDCON-1-STANDBY_READY : standby card is ready
RP/0/RSP0/CPU0:Mar 6 09:15:08.673 : rmf_svr[142]: %PKT_INFRA-FM-3-FAULT_MAJOR : ALARM_MAJOR :RP-RED-LOST-NNR :CLEAR :0:
User Access Verification
Username: lab
Password:
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#sh plat
Tue Mar 6 09:24:09.083 UTC
Node Type State Config state
--------------------------------------------------------------------------------
0/RSP0/CPU0 A9K-RSP880-SE(Active) IOS XR RUN NSHUT
0/RSP1/CPU0 A9K-RSP880-SE(Standby) IOS XR RUN NSHUT
0/FT0 ASR-9904-FAN OPERATIONAL NSHUT
0/1/CPU0 A9K-4X100GE-TR IOS XR RUN NSHUT
0/PT0 A9K-AC-PEM-V2 OPERATIONAL NSHUT
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#
RP/0/RSP0/CPU0:ios#sh install active summary
Tue Mar 6 09:24:12.488 UTC
Active Packages: 1
asr9k-xr-6.2.3 version=6.2.3 [Boot image]
RP/0/RSP0/CPU0:ios#
Ipxe boot using DHCP Server :
Preparing system for backup. This may take a few minutes especially for large configurations.
Status report: node0_RSP0_CPU0: START TO BACKUP
Status report: node0_RSP0_CPU0: BACKUP HAS COMPLETED SUCCESSFULLY
[Done]
Proceed with reload? [confirm]
On active and standby XR console, HIT CTRL-C to view BIOS MENU. Select option 3 to boot " IOS-XR 64 bit External network boot using DHCP setting".
If active and standby are not stopped at boot menu, they will continue booting with previously known / saved settings.
There is 10 seconds time to hit CTRL-C when below message is seen on screen.
If system is inactive in BOOT MENU for 30 minutes, watchdog resets the RP/RSP and system will try to boot using last known settings.
Booting IOS-XR 32 bit - Press Ctrl-c to stop
Booting IOS-XR 64 bit Disk boot - Press Ctrl-c to stop
Please select the operating system and the boot device:
1) IOS-XR 32 bit
2) IOS-XR 64 bit Disk boot
3) IOS-XR 64 bit External network boot using DHCP setting
4) IOS-XR 64 bit External network boot using ROMMON setting
(Press 'p' for more option)
Selection [1/2/3/4]: 3
IOS-XR 64 bit External network boot using DHCP setting
, Continue ? Y/N: y
Serial ATA Port 4 : SMART iSATA SHSLM32GEBCITHD02
Serial ATA Port 5 : SMART iSATA SHSLM32GEBCITHD02
Once active has booted up, select option 5 from boot menu on standby to boot from active RP/RSP if not sync .
---- END ---