Unified Communications Infrastructure

Hi...Need Help in TLS configuration

Hi all, In our LAB we have CUCM 7.1. For TLS configuration we created one SIP trunk profile as Secure TLS profile in this profile we I have given device security mode as Authentication , Incoming and Outgoing Transport Port as TLS and Port as 50...

Resolved! Connect CUCM 8.0 with CME 4.0

We have CME 4.0 in production, And I have installed cucm 8.0 in our lab, I want to connect cucm 8.0 with CME 4.0 so I can make the call from CUCM 8.0 and also able receive call on cucm.How should I do this?

cue voice mail backup and restore

tomorrow , i need to install NM-CUE module , instead a old NM-CUE-CE module.but some doubt about backup and restore operating .1) if in old module have 63 voice mail boxs ( it have 100 license about voicemails) , and new NM-CUE have only 60 licenses ...

Create Unity Connection Cluster 7.1(5)

Hi to all,We have CUCM 7.1.(5) cluster with one Unity Connection 7.1(5), and I want to create a Unity Connection Cluster with another server, can anyone help me?Best regards,Alberto

Resolved! Unity 8 virtual mailbox question

Folks - I am not sure this is the right board, but Ill give it a shot.We have setup a hunt group in UCM that also has a Virtual Mailbox. Is there a way to, without converting this to a call handler, have the voicemails left on this account show up on...

Upgrade to 6.1.5 TFTP impact

I`m looking through various posts regarding the above upgrade form 6.1.2 and understand I need to two upgrades - 6.1.2 to 6.1.3 then 6.1.5Question TFTP Phone loadsWhen the cluster gets upgraded the device defaults will change. Will it be good to stop...

Is there any way to disable the "Device Configuration" Screen under ccmuser options screen?

Hi,I am running Communications Manager 7.1.5.31900-3 and I am trying to enable users to set their own PIN numbers. The only way I know that this can be done is through CCM (not good from admin burden) and the User Options Screen. The problem with the...

Call blocking based on called number

Hi all experts.In CUCM 8 or CME 4.x/7.x, is it possible to block calls coming from (PSTN) with the following prefix+92 21 0345xxxxxxxLet me explain the scenario which is very simple.1) ITSP will be providing us sip trunk (30 channels)2) SIP trunk wil...

Right Fax Outbound Calling Issue

Hi, I am facing outbound calling issue in Right Fax (Version 9.3.2) and using CUCM 6.0 .There is no integeration with Microsoft Exchange.When i tried to send a fax via FaxUtility getting an Error : No Answer at Fax Number.Incoming fax working ...

Cost effective UC solution for small companies?

Hi,Imagine small business (less than 10 employees) want UC solution to explore unified messaging and hopefully reduce costs by eliminating voice PRI.Question:1)if I use Cisco UC 520, which IP phones are most cost efective? Any experience using non-Ci...

Resolved! Unity 4.2 OS migration from 2K to window 2003

Hi Team,I want to replace the OS of unity 4.2 running with Exchange 2000. Current OS is Window 2000 and new OS will be 2003 with Exchange 2003.I know, I have to take the back up with DIRT or cobra then fresh installation required.My question is that ...

Cisco IP IVR Route Point Registration issue

Hi,We have a Cisco IVR Server version running 4.5.It was associated with CCM 5.1.3.This was working fine without any issues.CTI Route Point was registered with the CCM Server.We migrated CCM Server to 7.1.5 on a new hardware.After migrating we tried ...

unity8 websa

Hi ,When i try to access the unity administration page from a remote machine viahttp:\\server ip\web\sa , the following message pop up.Unrecognized errorhr=0x80070005 (E_ACCESSDENIED)From: global.asa--Initialize()Does anyone have any idea?I have no p...

COBRAS Unity to Unity?

Do you think it is possible to go from Unity 4.0.5 w/ Exchange Onbox to Unity 7.1.5 with Exchange 2007 off box?

CCM7.1.3

HIWe are planning to transition IP Phone devices from one cluster 7.13 to another cluster running CCM to 7.1(3) there will be an Inter-cluster Trunk between the clusters. There are 180 IP phones. What is Cisco best practice?Thx for all of your suppo...