HiI have powered off virtual machine but have problem downloading vmdk files from datastore Vmware Esxi 6.7.Here is the message!This x.x.x.x page can’t be foundNo webpage was found for the web address: https://x.x.x.x/folder/Cisco%2520Prime%2520Colla...
Forum Posts
Hi everyone, there is a CUCM publisher and a subscriber in our cluster, the 'Cluster Security Mode' is set to '1', 'Device Security Profile' is set to 'Non-Secure Profile' in phone configuration, there is no Authentication, and Encrypted Config. The...
Got an error in CUCM while upgrading to "cmterm-88xx-sip.14-1-1-0001-125.k4.cop.sha512" for Cisco 8841"Warning Error encountered: The selected file is not valid. Please ensure that the COP/ISO file is intended for this release. MD5 Hash Value: 32:af:...
HiWe have mediasense 11.5 and have problem while playing the records. Conversations appear out of sync and participants appear to talk over one another. It seems that this problem occurres in longer calls and calls with silence .How can I resolve the...
Resolved! 7841 SIP Phone - Background Image
Can I get a positive confirmation that the 7841 SIP deskphone does not support custom background images? I have seen images on google that seem to show a 78xx looking phone with a snoopy screensaver or similar image and this lead me to believe that...
Good day team Please may you give me a second option on why when i pressing the voice mail button from the 1812 phone
Dear Team, Our customer reported an issue. Call forward not working. When a user press cfwdall softkey, the phone immediately responds with "call cannot be completed" IVR. The phone is not allowed to enter even a single digit. at the same time call...
Hi Everyone.Hope you all are doing well.I was just learning about SIP Normalization Script in my Lab Environment . I have two phone with extension 6001 and 6002 . I want to manipulate FROM header , where if i call from 6002 , it should show 60225588...
Dear everyone,I need to install 53 locales to our Call Managers. I created the ISO file contains 53 locale installers and tried to install from CUCM OS Administration. However, I can only install one by one locale installer and it takes me a lot of t...
We are getting an intermittent problem where the first number of the voice mail pilot is being put and the end. The vm pilot is 9358995. When certain users press the vm button on the phone, it is dialing 3589959. Sometimes we can reset the phone a...
Resolved! To test the failover of sip trunk
We are planning to test the failover of sip trunk by shutting down the primary interface to check if the calls are routing through the secondary sip trunk. I hope there is a configuration in cucm where we can choose the primary and secondary sip trun...
Hi, I am getting the LogPartitionHighWaterMarkExceeded alert from RTMT and i have tried to purge the logs by setting LWM to 20% and HWM to 25%. Then I've waited for 1 week with the above mentioned % and set back to the default value after one week. I...
I've got a 10.5(2) UCXN cluster that the customer wants to upgrade to 11.5(1)-23900. Off line upgrade of the pub went perfectly. Started off line of the subscriber, and it cannot seem to start. In pulling the logs, it appears to be failing becaus...
Hello all, I am trying to configure SNMP on PCD 11.5.1. I am using the below commands on CLI (no GUI for that on PCD) utils snmp config 1/2c community-string add utils snmp config 1/2c trap add utils snmp config 3 user add utils snmp config 3 trap ad...
Hi, We just install our collaboration infrastructure (CUCM and CUC) and find out that forwarded call by IVR from PSTN is not getting ringback tone (just dead air). Our call flow is like this: PSTN --> FXO Cisco4351 --> CUCM --> CUC --> IP Phone The I...
