cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
3189
Views
8
Helpful
17
Replies

Meet-me

jorgeacat
Level 1
Level 1

I need to configure the password to meet-me conference?

Someone how can i do it?

3 Accepted Solutions

Accepted Solutions

Jaime Valencia
Cisco Employee
Cisco Employee

meet-me does not provide passwords

anyone that can dial the number can join if it has been initiated.

you can try to join thru unity with the supervised transfer + announcement to determine if you accept or deny access

applies to all versions and flavors

HTH

javalenc

if this helps, please rate

HTH

java

if this helps, please rate

View solution in original post

Sorry for the delay. I've been swamped with some stuff. Here are the instructions of how it got it to work.

Regards,

Create a call handler for each of your Meet Me extension with the following settings:

Prifle Settings.

Owner ==> Subscriber (This would be your preference. Perhaps Help Desk, or general mailbox for conference bridges)

Extension ==> Meet Me extension.

Call Transfer Settings.

Transfer incoming calls to a phone?

Yes, ring this extension ==> Meet Me extension.

Transfer Type:

Supervise Transfer.

Rings to wait for: 2

If the number is busy ==> No holding.

Gather caller information:

Check,

Confirm (call can be accepted or dinied)

Ask Caller's name.

Messages Settings.

Message recipient: A selected subscriber. (owner of the call handler)

View solution in original post

It is not possible to password protect a meet me conference.

View solution in original post

17 Replies 17

Jaime Valencia
Cisco Employee
Cisco Employee

meet-me does not provide passwords

anyone that can dial the number can join if it has been initiated.

you can try to join thru unity with the supervised transfer + announcement to determine if you accept or deny access

applies to all versions and flavors

HTH

javalenc

if this helps, please rate

HTH

java

if this helps, please rate

I have this doc on getting meetme to work through Unity but can not get it to work. I know it should work but something is missing. Please look it over. I got it here too.

rlp.

Hi,

I wrote this document. What exactly is the problem you are having

Please rate all useful posts

I had found a detailed document that went through setting up Unity to do the supervised transfer + announce several years ago and can not locate it again.

Does anyone have a link to that document?

Thanks,

Brian

If anyone has it, I would like it too.

Randy

I have implemented the supervised transfer through Unity through instructions found int he forum (transfer to meet me). Let me revise it tomorrow at the office before I post it.

regards

hi ,any update?

Sorry for the delay. I've been swamped with some stuff. Here are the instructions of how it got it to work.

Regards,

Create a call handler for each of your Meet Me extension with the following settings:

Prifle Settings.

Owner ==> Subscriber (This would be your preference. Perhaps Help Desk, or general mailbox for conference bridges)

Extension ==> Meet Me extension.

Call Transfer Settings.

Transfer incoming calls to a phone?

Yes, ring this extension ==> Meet Me extension.

Transfer Type:

Supervise Transfer.

Rings to wait for: 2

If the number is busy ==> No holding.

Gather caller information:

Check,

Confirm (call can be accepted or dinied)

Ask Caller's name.

Messages Settings.

Message recipient: A selected subscriber. (owner of the call handler)

these are the Unity settings, what about ccm?

cti route point? but you can not give the cti route point the same extension as the meetme bridge number.

translation pattern?

Help!!!!!!!!!!

Randy

Hi

Do you know how to put password to meet me?

It is not possible to password protect a meet me conference.

Hi -

You can check out two Cisco applications, MeetingPlace and MeetingPlace Express. Both products allow meetings to be scheduled using meeting passwords.

Ginger

Ginger, thanks but do not want to have another server and program.

We are just looking for a way to have a way for Unity to dial the meetme bridge number. That way a subsriber can call the call handler and Unity will dial it so a phone user can be remote and doesn't have to be local to the phone soft key.

someone in this conversation sent his setting but only the Unity side. I need the ccm side too.

Randy

on CCM side just make sure the VM port can reach the meet-me DN, nothing else. it's the same as if you wanted to reach a phone

HTH

java

if this helps, please rate

HTH

java

if this helps, please rate