09-29-2016 11:50 PM - edited 03-19-2019 11:38 AM
Hi guys,
I have a CUCMPub and CUCMSub 8.6
I have added both CNF in the MRG.
When I try to do conference by pressing the CNF Softkey I can't have more than 3 participants. Why is that?
I then configured the Voice Gateway that has a PVDM2-64 for conferencing and then I added to its own MRG and put first the MRG in the MRGL.
When I did that and I tried to conference I saw that the DSPFarm was used but again the Max Conference parties where no more than 3.
I have provided the configuration. Where 192.168.150.2 <-CUCMSub and 192.168.150.1 <-CUCMPub
voice-card 0
dsp services dspfarm
sccp local Port-channel1
sccp ccm 192.168.150.1 identifier 2 version 7.0
sccp ccm 192.168.150.2 identifier 1 version 7.0
sccp
!
sccp ccm group 1
bind interface Port-channel1
associate ccm 1 priority 1
associate ccm 2 priority 2
associate profile 1 register CFB-VG
switchover method immediate
switchback method immediate
switchback interval 5
!
dspfarm profile 1 conference
codec g711ulaw
codec g711alaw
maximum sessions 5
associate application SCCP
!
ccm-manager sccp local Port-channel1
Show commands when already 3 conference participants active.
VG#show dspfarm all
Dspfarm Profile Configuration
Profile ID = 1, Service = CONFERENCING, Resource ID = 1
Profile Description :
Profile Service Mode : Non Secure
Profile Admin State : UP
Profile Operation State : ACTIVE
Application : SCCP Status : ASSOCIATED
Resource Provider : FLEX_DSPRM Status : UP
Number of Resource Configured : 5
Number of Resource Available : 5
Maximum conference participants : 8
Codec Configuration: num_of_codecs:2
Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required
Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required
SLOT DSP VERSION STATUS CHNL USE TYPE RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED
0 4 28.3.8 UP 1 USED conf 1 67811 2513 3160
0 4 28.3.8 UP 1 USED conf 1 67812 2513 3153
0 4 28.3.8 UP 1 USED conf 1 67815 2512 2522
0 4 28.3.8 UP 1 USED conf 1 67816 201 202
0 4 28.3.8 UP N/A FREE conf 1 - - -
0 4 28.3.8 UP N/A FREE conf 1 - - -
0 4 28.3.8 UP N/A FREE conf 1 - - -
0 4 28.3.8 UP N/A FREE conf 1 - - -
Total number of DSPFARM DSP channel(s) 5
VG#show dspfarm dsp active
SLOT DSP VERSION STATUS CHNL USE TYPE RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED
0 4 28.3.8 UP 1 USED conf 1 67811 6519 7166
0 4 28.3.8 UP 1 USED conf 1 67812 6519 7159
0 4 28.3.8 UP 1 USED conf 1 67815 6518 6527
0 4 28.3.8 UP 1 USED conf 1 67816 4207 4208
Total number of DSPFARM DSP channel(s) 1
VG#show dspfarm dsp idle
SLOT DSP VERSION STATUS CHNL USE TYPE RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED
0 4 28.3.8 UP N/A FREE conf 1 - - -
0 4 28.3.8 UP N/A FREE conf 1 - - -
0 4 28.3.8 UP N/A FREE conf 1 - - -
0 4 28.3.8 UP N/A FREE conf 1 - - -
Total number of DSPFARM DSP channel(s) 4
Solved! Go to Solution.
09-30-2016 06:46 AM
What is the "max add-hoc conference" set to in CUCM service parameters?
Are all participants attempting to join as G711 as that is the only codec you allow on your DSP farm?
09-30-2016 06:46 AM
What is the "max add-hoc conference" set to in CUCM service parameters?
Are all participants attempting to join as G711 as that is the only codec you allow on your DSP farm?
09-30-2016 07:06 AM
Refer this:
https://supportforums.cisco.com/discussion/13131246/meetme-conference-incoming-caller-limit
Edit to the O.P. G711 based conferencing is something that you can achieve with software CFB anyways so not sure why you are doing it through hardware based DSP resources. You probably need to allow other codecs such as G729 that you cannot do with software CFB on CM
Regards
Deepak
10-02-2016 11:20 PM
We have 7841, 7911, 7941, 7942, 7961, 7962 devices.
For example when I have a call from 7841 το 7841 the codec used is G.722.
Also when I have a call from 7941 to 7841 the codec used is G.722
@Deepak Rawat you are right. G711 based conferencing is something that you can achieve with software CFB
@Chris Deren "max add-hoc conference" was the problem and when I put more than 4 participants everything was OK.
I don't need to use DSPs
Thank you guys.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide