Unified Communications Infrastructure

cisco cme= the Red light on the handset don t work when i receive a message

hi,cme 2811, ios 15.1.3.T v1 i have configure the mwi dial peer dial-peer voice 123number 8000...mwi ondial-peer voice 124number 8001...mwi offwhen i call 8000217 ( 217 dn ) i have the the red light on and when i call 8001217 is off. but when i rece...

question about ISR router model

Dear all,Which kind of ISR router supports E1 , CME , and sip protocol?

query regarding Manager & secretary feature.

My requiremnet is given below,Secretary should be able to pick up managers phone and also if the manager doesn’t answer the call in 3 rings it should be forwared to secretaries extension. We dont want to user IMPA feature.Thanks

Unable to place calls to a single Cell User?!?!?

So check this out.CUCM 8.6 w/ MGCP to a PRI. Paetec is the Telco. Everything in this deployment has been working great for months except that outbound caller ID was being overwritten by Paetec to stamp our main number. Yesterday they removed the C...

Resolved! CUCM test

Hello i have a CUCM 8 usually i have a variance between the actual time and CISCO time about 5 min .when i set the time from cisco unified OS administration page, i notice that after 3 to 4 weeks the time changed back again to the old time.Can anyon...

CME with MS Lync

Is it possible to integrate CME with MS Lync?

SkyStone with CUCM 8.5

I have CUCM 8.5 and recently I purchased the SkyStone software. put I got difficulty to integrate the SkyStone with CUCM.could you please send me a step by step guide for this integration.Regards,

VMWARE NETWORK SETTINGS FOR CUCM 7

Hi ,1 - I am trying to install cucm 7 on vmvare and every time its unsuccessfull. I,m supecting that its failing due to network adepter settings of vmware.Please some one let me know what ip address I have to give in vmware network adopter & what ip...

Support of CUCM on ESX

I'm looking for clarification on support of CUCM 8.6. I realize Cisco doesn't support hardware other than HP & IBM platforms that UCS ships with. If you install CUCM on a different ESX platform, is the application supported but not the hardware or ...

Unity Cx 7.1.5 - Remove "Please wait while I transfer..."

In Unity Connection 7.1.5, is there a way to get rid of the "Please wait while I transfer your call" prompt when transfering to another subscriber? I would prefer to be able to do this on a call handler by call handler basis, but if there is a way t...

Where in BAT for “Users Associated with Line” field......

Hi All,I am trying to find where I can export all user lines via BAT to see if they have an assignment for “Users Associated with Line”.Basically, I have administered approx 1000 phones (some UDP and some not) however I was unaware that I needed to a...

Remote distination with mobile phone voice mail

Hi guys,I have a client who has remote distination with his mobile phone.He is asking to use his mobile phone voice mail instead of his Unity Connection voice mail all the time.I was thinking to set max timer under remote distination profile greater ...

Resolved! Cisco Unified Business Attendant Console 8.6

Hello Team,Have you found any issues with CUBAC support for 9971 phones? I have a client that runs the following:CUCM 8.5.1.13900-5CUBAC 8.6.2.119971: sip9971.9-0-2It works fine with the 7900 series, but not with the 9971. Basically I can see the in...

Cisco 7942, procurve switch, multiple vlan support

Hey folks,Have a CUCM 7.1.3 deployment (inherited). A remote site has a procurve switch (2610-48-PWR). The switch is carved up with ports 1-24 for data, 25-42 for Voice, 43-48 for "other" devices (wireless stuff primarily). 49-52 are tagged within ...