I am trying to install CUBAC version 8.0.X and during the installation it runs the database setup wizard. Whenever I click next it says "Unable to connect to server". CUBAC install SQL Express. Operating system is Windows 2008.
Hey all, installed 3 new subscibers to an existing, and I might add working, CM/Unity cluster. But for the life of me I can't figure out why the 3 new servers fail the UTIM "Verify Servers" test. The pub passes but not the three new subscribers. T...
I have a basic question that many may know the answer to. Cisco phones plugged into a CUCM 5,6,7,8x call manager - do the phones request the time from the CUCM cluster or does the CUCM cluster broadcast out the time to the phones? The question has be...
Hi all, In our LAB we have CUCM 7.1. For TLS configuration we created one SIP trunk profile as Secure TLS profile in this profile we I have given device security mode as Authentication , Incoming and Outgoing Transport Port as TLS and Port as 50...
We have CME 4.0 in production, And I have installed cucm 8.0 in our lab, I want to connect cucm 8.0 with CME 4.0 so I can make the call from CUCM 8.0 and also able receive call on cucm.How should I do this?
tomorrow , i need to install NM-CUE module , instead a old NM-CUE-CE module.but some doubt about backup and restore operating .1) if in old module have 63 voice mail boxs ( it have 100 license about voicemails) , and new NM-CUE have only 60 licenses ...
Hi to all,We have CUCM 7.1.(5) cluster with one Unity Connection 7.1(5), and I want to create a Unity Connection Cluster with another server, can anyone help me?Best regards,Alberto
Folks - I am not sure this is the right board, but Ill give it a shot.We have setup a hunt group in UCM that also has a Virtual Mailbox. Is there a way to, without converting this to a call handler, have the voicemails left on this account show up on...
I`m looking through various posts regarding the above upgrade form 6.1.2 and understand I need to two upgrades - 6.1.2 to 6.1.3 then 6.1.5Question TFTP Phone loadsWhen the cluster gets upgraded the device defaults will change. Will it be good to stop...
Hi,I am running Communications Manager 7.1.5.31900-3 and I am trying to enable users to set their own PIN numbers. The only way I know that this can be done is through CCM (not good from admin burden) and the User Options Screen. The problem with the...
Hi all experts.In CUCM 8 or CME 4.x/7.x, is it possible to block calls coming from (PSTN) with the following prefix+92 21 0345xxxxxxxLet me explain the scenario which is very simple.1) ITSP will be providing us sip trunk (30 channels)2) SIP trunk wil...
Hi, I am facing outbound calling issue in Right Fax (Version 9.3.2) and using CUCM 6.0 .There is no integeration with Microsoft Exchange.When i tried to send a fax via FaxUtility getting an Error : No Answer at Fax Number.Incoming fax working ...
Hi,Imagine small business (less than 10 employees) want UC solution to explore unified messaging and hopefully reduce costs by eliminating voice PRI.Question:1)if I use Cisco UC 520, which IP phones are most cost efective? Any experience using non-Ci...
Hi Team,I want to replace the OS of unity 4.2 running with Exchange 2000. Current OS is Window 2000 and new OS will be 2003 with Exchange 2003.I know, I have to take the back up with DIRT or cobra then fresh installation required.My question is that ...
Hi,We have a Cisco IVR Server version running 4.5.It was associated with CCM 5.1.3.This was working fine without any issues.CTI Route Point was registered with the CCM Server.We migrated CCM Server to 7.1.5 on a new hardware.After migrating we tried ...
