I think the answer to this is going to be no but just want to check. Other SBC vendors, such as Ribbon, offer a feature where the SBC can look at the called number in a received SIP Invite and then do a look up against Active Directory and route the ...
Forum Posts
I'm setting up SIP trunks on a CME system using sip phones. I've updated the IOS to c2900-universalk9-mz.SPA.157-3.M8.bin to take advantage of SIP tenant profiles. The SIP trunk appears to be up and registered.CME#show sip-ua register status tenant 2...
Hello,Can anyone provide some insight on this message that keeps appearing? The configuration isn't changing, but it seems to show up every 10-15 minutes.I've tried the workaround of adding EnableClusterCheck to the .xml file and set it to false, but...
Hi everyone I have issue on CMC in which when we tried to put CMC code the "#" sign was only adding up to the end of CMC code. Example is CMC code: 12345 >> Submit >> 12345# Submit >> 12345##. We tested also removing the CMC code required on the rout...
Hello , I have a cluster contains: CUCM01 , CUCM02, IM Presence 01 and IM Presence 02 with version 14.0.1The backup not passed it give me this message : unable to contact server. master or local agent could be down , on IM Presence 01 and IM Pre...
Hello,We have the following environment that needs to be upgraded to version 14 on new UCS servers with new IP addresses:- 1 CUCM-PUB and 1 CUCM-SUB- 1 IMP-PUB and 1 IMP-SUB- 1 CUC-PUB and 1 CUC-SUBI checked the online documentation and came to know ...
Anyone solved this issue when installing Cisco CUCM Version 14 I tried the following versions: 14.0.1.13900-155 and 14.0.1.12900-161 but I get the same and following error. I found some old discussions about this issue without a clear solution.
We have a exp E cluster that I'd figure should be able to resolve their FQDN but it doesn't seem to be the case. in the utility i punch in one of the FQDNs from the clustering page (different node), and it doesn't resolve in the dns utility. THere's ...
Hello all, I have a Cisco IM and presence v14.0.1 , but i can't start service cisco sync agent , do you have any idea to solve this problem ? Could you help me please Best regards
Resolved! CUBE without smart licensing
Hi, everyone. We have CUBE running on an ISR4331 with software version 17.06.05. We have not converted this to Smart Licensing yet, but ran into an issue when we lost connectivity to our ISP (not our SIP carrier). We could no longer make inbound or o...
Resolved! Some commands not available in router
Hello, I'm giving support to a customer that have a Cisco voice router 3825 running IOS version Version 12.4(7b) They are trying to configure some sip commands and they seem to be not availabl in the router: For example: 'ip address trusted list' and...
How to set the alarm for the phones that got unregistered from the CUCM. I tried to create a customized alert in the RTMT tool using RegisteredHardwarePhones under the performance counter area. But this alarm doesn't have detailed information, like t...
I have 3 ephone 2 of them have 1010 ,1020 number and I want to make the calls from fxo port comes on both of them so I make a voice hunt group with pilot number 30 , now I want to make barge to this number 30 if any of 1010 or 1020 have call from f...
Dear Collab Team, Recently we deployed CUCM 15.0.1. After that I installed the last UCCX 12.5SU3 (12.5.1.11003-511) with the patches: ES04 and ES04_special. However I stucked with the post-install CUCM-UCCX integration step (Cisco Unified CM Config...
Is there any way to install third-party software on CUCM or Cisco-customized Linux servers? We wanted to install the falcon sensors on these servers
