cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5462
Views
10
Helpful
11
Replies
Beginner

Expressway License C and E

Hi Experts,

I have received 2 PAK from Cisco for the Expressway. Understand that we need to install the VCS control and convert it to the Expressway C or E based on the license. Right?

Below is the PAKs I received from Cisco

1) LIC-EXP-E-PAK Expressway Series, Expressway-E PAK 1 (Expressway E License)
            After Extracted
                     - LIC-EXP-AN                     
                     - LIC-EXP-SERIES                
                     - LIC-EXP-GW                     
                     - LIC-EXP-TURN                   
                     - LIC-EXP-E

2) LIC-SW-EXP-K9 License Key Software Encrypted 1 (Release Key, only 1? C or E should I install the release key?)

May I know how do I convert it to the Expressway C ? Thanks.

1 ACCEPTED SOLUTION

Accepted Solutions
Contributor

Hi KelvinYou are missing 1

Hi Kelvin

You are missing 1 release key. You should have received 2 LIC-SW-EXP-K9. Usually the 2nd PAK is on the second page of the PDF.

For the LIC-EXP-E-PAK you should register for the following options one on each Expressway:
- LIC-EXP-SERIES
- LIC-EXP-GW

The following options are only needed on the Expressway-E:
- LIC-EXP-AN
- LIC-EXP-TURN
- LIC-EXP-E

HTH
Stefan

 

11 REPLIES 11
Advocate

Need to install the release

Need to install the release key first, then install the LIC-EXP-SERIES and LIC-EXP-GW to make an appliance Exp-C and install LIC-EXP-SERIES, LIC-EXP-GW, LIC-EXP-E, LIC-EXP-TURN and LIC-EXP-AN to make an appliance Exp-E.

Please rate useful posts.
Beginner

But there required the Serial

But there required the Serial Number. Would that possible to apply the release key in same PAK code but different serial number? How is it?

Thanks for your expert opinion.

Advocate

Yes, you have to do partial

Yes, you have to do partial fulfilment. Basically, select one of each of the part number above and put in the respective part number of the profuct you are activating. Repeat the above procedure for the other part number.
Please rate useful posts.
Beginner

Thanks George. Let me try on

Thanks George. Let me try on it. Thanks your valuable information. Appreciated.

Beginner

Hi, I tried to put in the

Hi, I tried to put in the same PAK code to generate another License for Expressway C. It seems doesn't work as it was with the Expressway E.

It showing completely fulfill in cisco.com/go/license

Advocate

At this point, you will have

At this point, you will have to contact licensing@cisco.com so that they should be able to help you further.

Please rate useful posts.

Re: Hi, I tried to put in the

Yes I have the same issue . And they only give answers like. Only put this, and this over that and thats all.
Contributor

Hi KelvinYou are missing 1

Hi Kelvin

You are missing 1 release key. You should have received 2 LIC-SW-EXP-K9. Usually the 2nd PAK is on the second page of the PDF.

For the LIC-EXP-E-PAK you should register for the following options one on each Expressway:
- LIC-EXP-SERIES
- LIC-EXP-GW

The following options are only needed on the Expressway-E:
- LIC-EXP-AN
- LIC-EXP-TURN
- LIC-EXP-E

HTH
Stefan

 

Beginner

Thanks Stefan,Your answer are

Thanks Stefan,

Your answer are valuable/details for me. Appreciate that.

Highlighted
Beginner

Re: Hi KelvinYou are missing 1

Hi Stefan,

 

Thanks for the clarifying answer!

 

Cheers,

 

Tássio Duarte

Beginner

Re: Hi KelvinYou are missing 1

Hi Stefan,

I have 4 PAK LIC-SW-EXP-K9 (i guess 2 for expressway-e and 2 for expressway-c) and 1 PAK LIC-EXP-E-PAK.

LIC-EXP-E-PAK contains following SKU:

LIC-EXP-E-PAK

1

LIC-EXP-RMS-PMP

6

LIC-EXP-DSK

70

LIC-EXP-E

2

LIC-EXP-TURN

2

LIC-EXP-AN

2

LIC-EXP-SERIES

4

LIC-EXP-MSFT-PMP

1

LIC-EXP-RMS

42

LIC-EXP-GW

4

Can you please advise which SKU should I apply for expressway-c and expressway-e.

CreatePlease to create content
Content for Community-Ad
August's Community Spotlight Awards