02-15-2011 11:27 AM - edited 03-19-2019 02:25 AM
Has anyone been successful in deploying FAC on CME 8.5 using lpcor? The solution I want is flat all external calls would require a FAC.
Solved! Go to Solution.
02-15-2011 10:46 PM
Following document talk about FAC on UC500. Should be good for CME.
02-16-2011 09:48 AM
It's also now in the CUCME System Admin Guide:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmefac.html
02-15-2011 10:46 PM
Following document talk about FAC on UC500. Should be good for CME.
02-16-2011 09:48 AM
It's also now in the CUCME System Admin Guide:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmefac.html
02-21-2011 03:50 PM
Hello ALL:
I used the 8.5 Guide to implement the FAC with lpcor. Currently if an lpcor is accepting calls from another group eg accept X, when I add accept X fac the calls go to a fast busy.
Any help really need to expedite the process.
11-30-2011 02:24 PM
!
voice lpcor enable
voice lpcor custom
group 10 Manager
group 11 LocalUser
group 12 RemoteUser
group 13 PSTNTRunk
group 14 IPTrunk
!
voice lpcor policy PSTNTRunk
service fac
accept Manager fac
accept PSTNTRunk fac
!
!
!
!
!
application
package auth
param passwd-prompt flash:enter_pin.au
param user-prompt flash:enter_account.au
param term-digit #
param abort-digit *
param max-digits 32
!
service clid_authen_collect
param uid-len 4
param pin-len 4
!
!
dial-peer voice 4 voip
corlist outgoing call-cell
destination-pattern 00.........
lpcor outgoing PSTNTRunk
session protocol sipv2
session target ipv4:10.86.3.50
voice-class codec 1
dtmf-relay sip-notify rtp-nte
no vad
!
!
!
ephone 3
lpcor type remote
lpcor incoming Manager
lpcor outgoing PSTNTRunk
device-security-mode none
mac-address DC7B.94F8.D8B4
type 7911
button 1:4
!
!
!
voice lpcor enable
voice lpcor custom
group 10 Manager
group 11 LocalUser
group 12 RemoteUser
group 13 PSTNTRunk
group 14 IPTrunk
!
voice lpcor policy PSTNTRunk
service fac
accept Manager fac
accept PSTNTRunk fac
!
!
!
!
!
application
package auth
param passwd-prompt flash:enter_pin.au
param user-prompt flash:enter_account.au
param term-digit #
param abort-digit *
param max-digits 32
!
service clid_authen_collect
param uid-len 4
param pin-len 4
!
username 1984 password 0 1984
==================================================
calls to the pstn
==================================================
!
!
ephone 3
lpcor incoming Manager
lpcor outgoing PSTNTRunk
device-security-mode none
mac-address DC7B.94F8.D8B4
type 7911
button 1:4
!
================================================================================
When this phone try to place outbound calls will be prompt to enter account and pin then tha call will be allowed
=================================================================================
!
dial-peer voice 4 voip
corlist outgoing call-cell
destination-pattern 00.........
lpcor outgoing PSTNTRunk
session protocol sipv2
session target ipv4:10.86.3.50
voice-class codec 1
dtmf-relay sip-notify rtp-nte
no vad
!
12-01-2011 05:57 AM
Hi All:
The issue was not the overall implementation but a trunk group that was being used. The guide pointed to applying the lpcor to the voice-port but when you use a trunk group you have to apply the lpcor under the trunk group settings for it to be effective. I had resolved the problem and the customer is now working fine.
It was actually when the customer requested a connection to a VoIP provider using a single port, that I was able to solve the problem. Thanks guys, not surprised you didn't see it as I had about 3 cases with TAC and they wouldn't solve it.
05-21-2014 05:48 AM
Hi,
I need to apply FAC for a user, but only for the calls begin with the digit 0 (for international) . All the calls beginning with any other digit should go without asking FAC.
I am giving my dial peer configuration below.
dial-peer voice 124 pots
trunkgroup ALL_T1E1
corlist outgoing call-international
description **CCA*INTERNIONAL**
translation-profile outgoing OUTGOING_TRANSLATION_PROFILE
preference 3
destination-pattern 9[0-9]T
forward-digits all
no sip-register
!
I want to aplly the setting for the user using this dail peer.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: