Dear all,
I'm preparing to setup Media Proxy recording solution for CUCM 12.5 with multiple Recording Logger.
In my Lab testing environment, I setup 2 sets of CSR1000V virtual CUBE in Box-to-Box HA, in latest version 17.3.2. They are registered onto my Smart Software Manager On-Prem for Smart Licensing. Media Proxy configuration is properly done on both vCUBE as below extracted. (There is only one Recording Logger at my Lab.)
(Both vCUBE with same configuration, except for the local interface IP Address)
!
voice service voip
ip address trusted list
ipv4 192.168.20.0 255.255.255.0
ipv4 192.168.41.0 255.255.255.0
allow-connections sip to sip
redundancy-group 1
trace
sip
bind control source-interface GigabitEthernet1
bind media source-interface GigabitEthernet1
session transport tcp
!
!
voice class uri 131 sip
host ipv4:192.168.20.131
!
...
!
media profile recorder 1001
media-recording proxy 1001
!
media class 1001
recorder profile 1001 siprec
!
...!
redundancy
application redundancy
group 1
name vCUBE-HA-1
priority 99 failover threshold 5
timers delay 30 reload 60
control GigabitEthernet2 protocol 1
data GigabitEthernet2
track 1 shutdown
!
!
!
!
!
!
!
track 1 interface GigabitEthernet1 line-protocol
!
...!
interface GigabitEthernet1
ip address 192.168.20.1 255.255.255.0
negotiation auto
no mop enabled
no mop sysid
redundancy rii 1
redundancy group 1 ip 192.168.20.3 exclusive
!
interface GigabitEthernet2
ip address 192.168.1.1 255.255.255.0
negotiation auto
no mop enabled
no mop sysid
!
...!
dial-peer voice 1001 voip
destination-pattern 1001
session protocol sipv2
session target ipv4:192.168.41.101
session transport tcp
codec g711ulaw
!
dial-peer voice 1000 voip
session protocol sipv2
session transport tcp
incoming uri via 131
media-class 1001
codec g711ulaw
!
...!
call-home
! If contact email address in call-home is configured as sch-smart-licensing@cisco.com
! the email address configured in Cisco Smart License Portal will be used as contact email address to send SCH notifications.
contact-email-addr sch-smart-licensing@cisco.com
profile "CiscoTAC-1"
active
destination transport-method http
destination address http http://ssm-on-prem-7.etphonehome.hkt.local/Transportgateway/services/DeviceRequestHandler
no destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
ntp server 128.9.176.30
!
!
Since the vCUBE is running version 17.3, I expect it would automatically request license required (expected to be Media Proxy license "CUBE-MP-RED") at my Smart Account via SSM-on-Prem. But, I found that CUBE Trunk Redundant Session license (x2) has been request from the vCUBE.
Does anyone have idea about the following?
- Why CUBE Trunk License has been request?
I expect my configuration has no SIP Trunk setup. There should be Media Proxy only.
Do I have any configuration wrong? - The 2 vCUBE are expected to be working in Box-to-Box HA pair. Why 2 Session Licenses are request? Why not 1?
Do I have any configuration wrong? - When my Recording Phone (at CUCM) is in conversation, recording is success.
But, at that moment, no Media Proxy session license has been request. Why?
Best regards,
E. TSE
