cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

504
Views
45
Helpful
16
Replies
Donaire
Beginner

No Voice commands found on cisco router

Hey guys, 

I cannot find voice commands on cisco router series 2900, 

I have licended it, but no luck

 

Command: voice service voip

 

NT: Setting up on a packet tracert

2 ACCEPTED SOLUTIONS

Accepted Solutions

Yes,  those can handle SIP trunk.

 

Make sure you have UC license.



Response Signature


View solution in original post

The physical hardware for 2900 absolutely support this command with the appropriate license. It’s likely the simulator that does not have support for the specific command.



Response Signature


View solution in original post

16 REPLIES 16
Nithin Eluvathingal
VIP Advisor

license boot module module-name technology-package package-name

 

Refer below link for how to do Software Activation on Cisco Integrated Services Routers

https://www.cisco.com/c/en/us/td/docs/routers/access/sw_activation/SA_on_ISR.html

 

Make sure you have UC license. 

 

 

 

 



Response Signature


Hi @Nithin Eluvathingal 

Its activated but i still can´t get the router to accept the command

 

Technology Package License Information for Module:'c2900'

 

----------------------------------------------------------------

Technology Technology-package Technology-package

Current Type Next reboot

-----------------------------------------------------------------

ipbase ipbasek9 Permanent ipbasek9

security disable None None

uc uck9 Evaluation uck9

data disable None None

Have you reloaded the router after activating the software package  ?

 

 

 

 

 



Response Signature


@Nithin Eluvathingal 

thans for the reply, 

 

I have used the following: 

 

write memory

copy running-config startup-config

reload, 

Is that a packet tracer ? If  yes,  AFAIK not all voice  commands are possible on a   packet tracer. 

 

Informations which  I shared are for real routers.

 

 



Response Signature


Thanks, 
That seems to be the problem. 
As im going to implement it on a real router, can you just please confirm if the series 2900 can handle  SIP Trunk ?

Yes,  those can handle SIP trunk.

 

Make sure you have UC license.



Response Signature


View solution in original post

Elliot Dierksen
Enthusiast

Please provide the output of a "show version" and a "show license". It is almost certainly either the incorrect IOS image or the licensing isn't activated. Also please add the output of "show run | i boot".

Hi @Elliot Dierksen 
Here it is:

Router#sh version

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Thurs 5-Jan-12 15:41 by pt_team

 

ROM: System Bootstrap, Version 15.1(4)M4, RELEASE SOFTWARE (fc1)

cisco2911 uptime is 1 hours, 4 minutes, 41 seconds

System returned to ROM by power-on

System image file is "flash0:c2900-universalk9-mz.SPA.151-1.M4.bin"

Last reload type: Normal Reload

 

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

 

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

 

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco CISCO2911/K9 (revision 1.0) with 491520K/32768K bytes of memory.

Processor board ID FTX152400KS

3 Gigabit Ethernet interfaces

DRAM configuration is 64 bits wide with parity disabled.

255K bytes of non-volatile configuration memory.

249856K bytes of ATA System CompactFlash 0 (Read/Write)

 

License Info:

 

License UDI:

 

-------------------------------------------------

Device# PID SN

-------------------------------------------------

*0 CISCO2911/K9 FTX1524GRWN-

 

 

Technology Package License Information for Module:'c2900'

 

----------------------------------------------------------------

Technology Technology-package Technology-package

Current Type Next reboot

-----------------------------------------------------------------

ipbase ipbasek9 Permanent ipbasek9

security disable None None

uc uck9 Evaluation uck9

data disable None None

 

Configuration register is 0x2102

 

***********************************************************

Router#sh license all

License Store: Primary License Storage

StoreIndex: 0 Feature: ipbasek9 Version: 1.0

License Type: Permanent

License State: Active, In Use

License Count: Non-Counted

License Priority: Medium

 

License Store: Evaluation License Storage

StoreIndex: 0 Feature: securityk9 Version: 1.0

License Type: Evaluation

License State: Active, Not in Use, EULA accepted

Evaluation total period: 208 weeks 2 days

Evaluation period left: 208 weeks 2 days

Period used: 0 minute 0 second

License Count: Non-Counted

License Priority: None

StoreIndex: 1 Feature: datak9 Version: 1.0

License Type:

License State: Active, Not in Use, EULA accepted

Evaluation total period: 208 weeks 2 days

Evaluation period left: 208 weeks 2 days

Period used: 0 minute 0 second

License Count: Non-Counted

License Priority: None

StoreIndex: 2 Feature: uck9 Version: 1.0

License Type: Evaluation

License State: Active, In Use

Evaluation total period: 208 weeks 2 days

Evaluation period left: 208 weeks 2 days

Period used: 0 minute 0 second

License Count: Non-Counted

License Priority: None

 



collinks2
Contributor

Which mode did you try to enter the command?

 

 

Hi @collinks2 

 

Configuration mode

Router(config)# 

collinks2
Contributor

You are right. I tried to enable it in 2900 on the packet tracer but not found.

I have enabled it on the csr 1000 Router (virtualized).

Probably this command is not supported on 2900 router. Howevee,am still checking

@Donaire On a regular 2900 router that command is definitely available. Can you please share the output of “sh inv”. Not sure what you mean by packet tracer?



Response Signature


Hi @Roger Kallberg 

I mean, im using the simulator Cisco packet tracer. 
The show inventory command is not available on the simulator cisco packet tracer. 

I not sure, but i guess this limitation is only on the simulator. 
I am having network environment where by i need to make the router communicate with a PBX, 
Im still wainting for the uc license therefore i was testing on the simulator, but seems I cannot use this command there. 

I am afraid the series 2900 cannot support this, but all datasheet says it supports sip trunk.

Create
Recognize Your Peers
Content for Community-Ad