02-23-2018 03:49 AM - edited 03-19-2019 01:10 PM
We have configured SRST at Remote branch.
Please find configuration.
Please let me know if is there any changes in this configuration.
I have one question should i create dial-peer for incoming call.
call-manager-fallback
max-conferences 8 gain -6
transfer-system full-consult
ip source-address 10.108.20.6 port 2000
max-ephones 50
max-dn 50
system message primary SRST Active
keepalive 20
ccm-manager fallback-mgcp
application
global
service alternate default
voice service voip
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
sip
bind control source-interface GigabitEthernet0/0/0
bind media source-interface GigabitEthernet0/0/0
registrar server expires max 1200 min 60
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice register global
esrst
timeouts interdigit 5
system message "SRST Mode"
max-dn 50
max-pool 50
voice register pool 1
id network 10.108.22.0 mask 255.255.255.0
no digit collect kpml
voice-class codec 1
voice translation-rule 1
rule 1 /^62726\(6..\)$/ /6\1/
!
voice translation-rule 2
rule 1 /^62726\(5..\)$/ /6\1/
!
!
voice translation-profile SRST1
translate called 1
!
voice translation-profile SRST2
translate called 2
!
voice-port 0/1/0:15
translation-profile incoming SRST1
!
voice-port 0/1/1:15
translation-profile incoming SRST2
!
DID range =627266XX
dial-peer voice 11 pots
description "SRST_LOCAL_MOB_CALLS"
incoming called-number 66..
destination-pattern 9[7-9].........
port 0/1/0:15
forward-digits 10
!
dial-peer voice 12 pots
description "SRST_LOCALCAllS"
incoming called-number 66..
destination-pattern 9[1-7].......
port 0/1/0:15
forward-digits 8
!
dial-peer voice 13 pots
description "SRST_STDCALLS"
incoming called-number 66..
destination-pattern 90[0-9].........
port 0/1/0:15
forward-digits 11
!
dial-peer voice 14 pots
description "SRST_ISDCALL"
incoming called-number 66..
destination-pattern 900T
port 0/1/0:15
prefix 00
DID range =627265XX
dial-peer voice 1 pots
description "SRST_LOCAL_MOB_CALLS"
incoming called-number 65..
destination-pattern 9[7-9].........
port 0/1/1:15
forward-digits 10
!
dial-peer voice 2 pots
description "SRST_LOCALCAllS"
incoming called-number 65..
destination-pattern 9[1-7].......
port 0/1/1:15
forward-digits 8
!
dial-peer voice 3 pots
description "SRST_STDCALLS"
incoming called-number 65..
destination-pattern 90[0-9].........
port 0/1/1:15
forward-digits 11
!
dial-peer voice 4 pots
description "SRST_ISDCALL"
incoming called-number 65..
destination-pattern 900T
port 0/1/0:15
prefix 00
Solved! Go to Solution.
02-26-2018 01:34 PM
Hi,
use de following debug and send the log please:
debug voice ccapi inout
Best regards,
Marcelo Morais
02-24-2018 02:08 PM
Hi,
the incoming called-number command is one of the responsible for the dial-peer incoming calls, to make the dial-peer more clear you can remove all the incoming called-number commands and insert the following lines:
dial-peer voice 66 pots
description "SRST_INCOMING_FROM_PSTN 0/1/0"
incoming called-number 66..
direct-inward-dial
port 0/1/0:15
dial-peer voice 65 pots
description "SRST_INCOMING_FROM_PSTN 0/1/1"
incoming called-number 65..
direct-inward-dial
port 0/1/1:15
Hope this helps,
Marcelo Morais
02-25-2018 07:52 PM
Hi Marcelo,
I have configured this but getting issue
Cause i = 0x8292 - No user responding
02-26-2018 01:34 PM
Hi,
use de following debug and send the log please:
debug voice ccapi inout
Best regards,
Marcelo Morais
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: