cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
1051
Views
0
Helpful
10
Replies
Highlighted
Beginner

VG350 Gateway Configuration

 

Hello Guys,

 

Can someone please help me with the sample configuration of VG350 analog gateway.

 

i want to configure it with CUCM 11.5 and register analog phones and FAX machines.

 

VG350 is new for me and i am not sure what is the best way to configure it.

 

Someone please help me with sample configuration.

10 REPLIES 10
Highlighted

Re: VG350 Gateway Configuration

There is nothing novel or unique about the VG350 from a configuration perspective. Choose your control protocol - SCCP vs. MGCP - and then configure it as a gateway in CUCM along with the typical baseline config you would use. Here’s a quick link assuming you want MGCP:

https://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-communications-manager-callmanager/42105-vg200-cfg.html

Highlighted
Beginner

Re: VG350 Gateway Configuration

 

Thanks for reply. I went through this post, seems pretty old one.

 

It also state below, 

Caller ID does not work on FXO ports. This is because caller ID is not supported with FXO ports when configured for MGCP. Configure the gateway in H.323 mode instead”

 

Is this also applicable with VG350 as MGCP  in 2018 ?

Highlighted

Re: VG350 Gateway Configuration

Did you add a VIC3-FXO card to the VG350 EHWIC slots? This isn't a standard component of a VG350. If yes, then the article is correct should you require caller ID: the FXO card would need to use H.323 or SIP. That doesn't preclude you from using MGCP or SCCP for the FXS ports though.
Highlighted
Cisco Employee

Re: VG350 Gateway Configuration

DUPLICATE
https://community.cisco.com/t5/ip-telephony-and-phones/vg350-support-for-fax-and-modem-when-configured-as-sccp/td-p/3703638

Nipun Singh Raghav
"We cannot solve our problems with the same thinking we used when we created them"
Highlighted
Enthusiast

Re: VG350 Gateway Configuration

Hi Aniket,

 

I am also going to configure VG 350, 320 and 310 with CUCM 11.5.

Please advise if you have done configure it and working proper. Please share me VG configuration of working Analog VG...

Thanks

 

Warm Regard's
Amit Sahrma
Highlighted
Rising star

Re: VG350 Gateway Configuration

I have wrote a very detailed guide to my team of how to configure VG using SCCP.

If you want, I can share it with you internally via PM.

Highlighted
Enthusiast

Re: VG350 Gateway Configuration

Thank you so much for your support and quick response.. please share the guide with me..
Warm Regard's
Amit Sahrma
Highlighted
Beginner

Re: VG350 Gateway Configuration

Hi,

I am first time configure the vg 310.

Colud you please share me the vg 310 configuration.

 

 

Thanks in advance

 

Highlighted
VIP Collaborator

Re: VG350 Gateway Configuration

Hi,

Please see attached VG3XX configuration template using SCCP protocol and actual configuration of VG310.

 

 

Please rate helpful posts and if applicable mark "Accept as a Solution".
Thanks, Vaijanath S.
Highlighted
Beginner

Re: VG350 Gateway Configuration

Hi Slavik, 

 

Can you share with me your guide. Now I am configuring VG310 for polycom analog phones and fax. I connected to CUCM to vg310 with SCCP. and now i can not use conference feature, also second line on phones don't appear

CreatePlease to create content
Content for Community-Ad
Future of Work Virtual Summit Day 5

Cisco COVID-19 Survey