cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
1394
Views
10
Helpful
10
Replies
sylvain2006
Beginner

vwic3-2mft could not download P4SM RESET RELEASE

Hi all

I have my voice gateway C2901, when i install a vwic3-2mft -t1e1 card, router do not recognize it.

But with sh inventory command, i notice that vwic3-2mft card appear.

With console log i have this error

*Dec 1 08:49:50.495: %PVDM-6-UNSUPPORTED: Codec G.723 is not supported on PVDM3.
*Dec 1 08:49:57.871: Could not release P4SM reset, MISC_CONTROL(0xFFFFFFFF)
*Dec 1 08:49:57.871: %HWIC_T1E1-1-FPGADNLDFAIL: HWIC_T1E1 0: FPGA download failure; could not download P4SM RESET RELEASE.

 

command sh inventory

NAME: "CISCO2901/K9", DESCR: "CISCO2901/K9 chassis, Hw Serial#: FGL173221HB, Hw Revision: 1.0"
PID: CISCO2901/K9 , VID: V06 , SN: FGL173221HB

NAME: "VWIC3-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 1", DESCR: "VWIC3-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC3-2MFT-T1/E1 , VID: V01 , SN: FOC172873U2

NAME: "PVDM3 DSP DIMM with 32 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 32 Channels"
PID: PVDM3-32 , VID: V01 , SN: FOC19127KQS

NAME: "C1941/C2901 AC Power Supply", DESCR: "C1941/C2901 AC Power Supply"
PID: PWR-1941-2901-AC , VID: , SN:

 

Interfaces that appear

Cisco CISCO2901/K9 (revision 1.0) with 483328K/40960K bytes of memory.
Processor board ID FGL173221HB
2 Gigabit Ethernet interfaces
1 terminal line
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)

License package

Technology Package License Information for Module:'c2900'

-----------------------------------------------------------------
Technology Technology-package Technology-package
Current Type Next reboot
------------------------------------------------------------------
ipbase ipbasek9 Permanent ipbasek9
security securityk9 Permanent securityk9
uc uck9 Permanent uck9
data None None None

 

IOS

System image file is "flash0:c2900-universalk9-mz.SPA.152-4.M4.bin"

Can Someone help me?

1 ACCEPTED SOLUTION

Accepted Solutions

If possible try a different VWic card.: good solution

 

View solution in original post

10 REPLIES 10
Nithin Eluvathingal
VIP Mentor

I have my voice gateway C2901, when i install a vwic3-2mft -t1e1 card, router do not recognize it:- what you mean by not recognising? Since you can see it on show inventory the card is recognised.

 

You need to use card type command before configuring the controller 

 

The T1/E1 HWICs or network module will not be operational until a card type is configured.

SUMMARY STEPS

1. enable

2. configure terminal

3. card type {t1 | e1} slot subslot

 



Response Signature


Hi

Card type command doesn't work 

 

command card type isn't supported with 

(config)#card type t1 0 2
                      ^
% Invalid input detected at '^' marker.

Did you tried a reboot.. reinsert the card and reboot.  check if it makes any difference. 



Response Signature


Did you tried a reboot.. reinsert the card and reboot : yes but nothing

and i uploaded a new ios but nothing 

If possible try a different VWic card.

 

https://quickview.cloudapps.cisco.com/quickview/bug/CSCua50697

Have a look on above bug ID



Response Signature


If possible try a different VWic card.: good solution

 

@sylvain2006 why did you mark your own reply as the answer when it was really @Nithin Eluvathingal that gave you the correct answer?



Response Signature


@sylvain2006 why did you mark your own reply as the answer when it was really @Nithin Eluvathingal that gave you the correct answer? :  It's an error

If it was an error why do you not change it?



Response Signature


 

When i said It's an error:  i wanted to say that i was wrong 

But i didn't want to give myself the solution

 

Create
Recognize Your Peers
Content for Community-Ad