First time working on a UCS server. I have a new C2205 M5 that I'm setting up. Two drives are installed, and are present under physical drive info in CIMC & SCU. But, neither drive is listed as an available physical drive to configure for RAID. In C...
Forum Posts
HiThe NPIV/NPV in UCS blade is not properly configured, the UCS blades are B200 M5 seriesThe SAN storage is provided through MDS9706 fabric and the NPIV protocol is able on MDS fabrics and working for Oracle virtual machine and AIX/vios environmentsT...
Hi Can anybody please advise on the below, I am recieving this error, however the cluster itself is healthy KERN-2-SYSTEM_MSG: [112916207.001611] mts_do_msg_input() failing since no space available in 2288 (src_sap = 2288, opc = 7679) - kernelsvc_sam...
HiWe have have an updating server profile template applied to five blades to configure for booting from a SAN via iSCSIFirst time we have set this up so the learning curve has been steep and we discovered that each server needs a separate target init...
Resolved! Disable memory dimms on C240
Hello, I am looking for a way to disable some memory modules in a C240 M5 server.Is there a "software" way (e.g. via certain policies) besides physical removing them? The server is managed via UCS Manager. Regards Martin
Hi All,I have an alert for the CMOS battery on the system board of a blade server in a Cisco UCS B440 M2.- CIMC | Voltage P3V_BAT_SCALED #0x00 | Lower Non-critical - going low | Asserted | Reading 2.42 <= Threshold 2.42 Volts I reviewed the sensors a...
Hello all,I have a fully populated 5108 chassis with 8 x B200 M5 servers.The chassis has 4 power supplies which are configured in a grid mode.Power supply 1+2 are connected to the same PDU and power supply 3+4are connected to a different PDU.What wil...
hai, i have CIMC eror, "Reboot and select proper boot device or insert boot media in selected boot device and press a key." before is normal, but after i reboot, the problem is come. please help me thanksRT
We have 4 new B200 M5 with 768GB of RAM. I have had memtest running over the weekend and now when I look all 4 of them have memory error. I've attached screenshot from one of the servers Can all 4 really have memory error or can it be some configurat...
Is it possible to make disks connected to Cisco UCSC RAID SAS 2008M-8i (SLOT-MEZZ)visible/handled by the BIOS? Like some sort of HBA mode. I need to install CentOS 8, and the drivers for this RAID controller has been removed. Product Name: UCS C220 M...
Hello, I have questions about UCS240 server . It is M5 rack server . When i was upgrading hardware , accidently , the PCi slot frame , has gone inside partly and stay there . Will it cause any problem to the running server. ?It is only the frame t...
Hello all,Is it possible to run a C220 M5 server with one power supply plugged into 220V and the other power supply plugged into 110V at the same time?Appreciate any response,Ron
Hi Team, We are planning to UCCE upgrade from v10.5 to v12.0 to one of our customers and ordered UCE C240 and C220 servers. For Business editions servers, ESXI is pre-installed and the same ISO is placed in the datastore for future use. In our case, ...
Hello community Hope someone can shed some light on this topic.So we have a UCS B200M5 with FI6454. We are using this in a FlexPod environment with a NetApp AFF NFS storage. We have configured for service profile with 2 vNIC templates for NFS storage...
I tried to upgrade the firmware of S2360 from 4.0.1a to 4.0.4h or 4.0.4k using UCSM, CIMC and HUU but each time the CMC update fails. All the other components were updated successfully. The 4.0.4k appears as the backup fw for the CMC although it was ...
