When I look at the 'show configuration' output of the service profile on the CLI, i do not see the information of the inband configuration. Where would I see this from the CLI. UCSM 3.2.2
Forum Posts
Hi, I need some quick inputs. Is there any Nexus 6K switch which includes Nexus 2K bundles? Can we buy both together in a single bundle to reduce the cost? If such option is available, can you please provide me the ordering part number? Thanks in adv...
We have a Hardware fault with of the UCS blade’s Processors. UCS blade is unable to recover Purple screen of Death even after reboots. Once rebooted blades has crashed on below blank screen can’t go further than Selftest
i want to know ucs backup all configration vs full state different, that is full state Completely contain all configration ? what means state in the word of full state? i understand this is use full state include the service profile map to servers r...
Hi Allwe plan to move to hyperflex from our UCS but not all servers we will move only the consumes more resources so now I need to collect the UCS Information, such as CPU , CPU Cores, CPU usage % Memory, Memory usage % etc .. by each blade and bett...
Hi to All,We are on the process of deploying 2 Nexus 7k, 2 nexus 5K and a bunch of nexus 2k in our data center, we use vPC inside our data center, we do have UCS is our DC which is currently connected to our 6509E core switch via port channel with 1G...
hi and good day,This is my first time posting for this community corner and i just hope i didn't violate any rules for the first time poster. :DI am using Nexus 1000v in our Cloud Service, we have 4 Blade ESXi clustered host and 2 Nexus 7000 directly...
Hi, We have a Nexus 1000v environment running version 4.2(1)SV2(2.2). I am trying to remove a host but there is a vethernet port that has a partial configuration and I can't remove the host because the port is "in use". There was a VM that was ...
I have a UCS mini with 2 uplinks from each 6324 connected to a 3850 stack. I have cabled it so 6324-A is connected to port ten1/0/1 and ten2/0/1 (po1 on the 3850's), and 6324-B is connected to port ten1/0/2 and ten2/0/2 (po2 on the 3850's). I have ...
I have a HX DP installer running on my laptop. I set it to use DHCP to get IP address. It works fine however I am wondering how I can change it to a specific static IP address? The same process as change IP for a ubuntu linux? Can not find informatio...
Resolved! ucspe import backup xml some questions
1.i use ucsp 3.1 backup type system configuration&logical from local ,but inoperative. 2.if i use ftp server backup xml file,that's faild. that's not support in ucspe3.1??? 3.last i want know ucspe 3.1 support ldap ?? [nät] 不 [Bù] 副词 不; 未; 无...
Hi,Which of the below commands works better for automating the server acknowledge via Power Tool.Set-UcsBladeor Confirm-UcsServerwhat would be the exact syntax for these commands?Thanks in advance.
Hi All,How to configure SAN Boot on the UCS C Series platform ? On B Series, we can configure the boot order from vHBA, but on the UCS C Series I found nothing.The C Series SAN boot had being enabled and also the boot target was configured on the vHB...
Hi, I would like to use a iSCSI storage for my ESXI install. I did successful install in the past, where the OS was able to find the storage via iBFT. Now, on my system running the 2.2.8 fw, whatever I try, the iBFT table is empty and the OS is unabl...
hello, I'm a little entity that is building a rack with 5 esxi 6.5U1 hosts in vsan with vDS as virtual to physical network. Each hosts have a dual 10Gb SFP+ nic for vSAN VLAN, vMotion VLAN and high traffic VM Network VLANS and a quad 1Gb RJ45 nic for...
