HI all, I am getting "SFP validation failed " error after inserting GLC-T connector in 5548 nexus switch.Is thre any seperate config required for GLC-T connector.Regards,Ajith
im having a certain bug with my ucs c220 m35 and i need a certain patch , the issue is that there is previous patches to the one i need so do i need to install all the previous ones or i can install the one i need right away?
i need to change the network adapter on my ucs c220 m35 vm machines from E1000E into vmxnet3 , can i simply delete the network adapter on the vm machines and add the other type? can it cause the vm machine to fail?
We connected an external USB drive to the doogle of our UCS B200 Blade. We have OVM Server installed on the blade, but the USB drive is still not visible. Do I have to enable a specific setting on the service profile? We have checked enable on USB...
Hello,
New to networking implementation and design. Having issues with CIMC inband issue with UCS-B series.I setup a packet capture on the fabric interconnect A uplink. I can see ARP for the CIMC inband IP address. But no reply from UCS. I disabled ...
Hi folks,
In the "UCS-C220 M3" side, we are using the 10-GE SFP+ Module "CDE2-SFP-1WSR" (for Intel X520 Dual Port 10Gb SFP+ Adapter), so we want to know wich "10-GE SFP+ Module" we have to use in the Switching side (for Cisco Nexus 7700)??
The only d...
Needing to decide - we want/need a simple/clean upgrade experience that can occur in one pass, so that we can install new B200M4 blades and upgrade ESXi hosts to vSphere 6 u2
The download tool seems to recommend 3 possibilities:
2.2(3j)
2.2(6f)
3.1...
I am having an issue with a UCS C220 M3S running firmware 2.0 (1b) it crashed on Friday and caused a purple screen, so we have logged it with
VMware to assist me but I was wondering if you could advise how to read the Technical Support Data and if t...
Dear All,can any one help m I have an error "Adaptor host interface 1/2/1/1 link state down" and none of my nics will come up state "up" F0207 error. I am running 2.2(6f) and the chassis policy as port channel, set the server ports as two for each F...
i came today morning to find my ucs c220 m35 has crashed over the weekend , i hard reset it and it went up fine along with all the vm "it had four solarwinds windows vm" , the problem is now im asked to find the root cause of the crash and frankly i...
i have a ucs c220 m35 with a cimc ip address that i can ping but i can't access on the browser through https? i restarted it and it is still the same , also i tried different pc and browsers yet i can't open cimc page. any idea how to resolve this ??...
Hi,we have just upgraded ucsCentral to 1.4.1a,we are working on planning the update of all our ucsm infra bundle to 1.3.1 FW.Any one doing this that could tell me if the process is the same as pushing the FW trough the automatic method in the UCSM gu...
Hi people,
FlexPod is know for boot your virtual machines from SAN, There is some deployment guide for FlexPod and UCS Mini?
I have problems with the configuration of UCS Manager to provide connectivity to SAN storage. The Scenario diagram is attac...
Customer must migrate a UCS domain to another location.
Is there a safe graceful shutdown of the fabric interconnects. I'm paranoid just unpluging the power as I've seen too many cases with file corruption, and therefore ending up in boot prompt.
Hi everyone . recently i made 1 blade server working. I installed Windows 2012 R2.
That before i got a problem with 4K HDD.
But when i put a bootloader path it worked but i dont know what is the connection between the bootloader and the windows boot...
