Unified Computing System Discussions

Hello, We bought 5 UCS C24M3 standalone servers for one of our customer with raid controller UCS-RAID9270CV-8I but the Supercap (battery) seems to be missing so only write through cache policy is possible (instead of write back cache policy) ==> resu...

Hello,I'm facing an issue on a UCS C220.When I launch a VKM session, the VM tab doesn't appear.I've already checked if the Console Base vMedia properties was enabled and it is.I've already tried to Disable KVM and enable it again with no further resu...

Hi all,My context :I want to do iSCSI boot from UCS to Netapp.My blades are B230 M2 with VIC1280 with FI 6248.Upstream switch is Catalyst 4500X with port channel connected to FI6248 (trunk native vlan 504).I do all the configuration described here ht...

Unable to open KVM's from UCS KVM Console, Windows 2008 R2 with Java installed try in IE and Firefox, I am able see all KVM's but when I click on KVM it will ask for save or open, saving to disk and opening from disk, directly open not working. Any c...

I am deploying vSphere 5.5 to a group of B-420-M3 , fw level 2.2.(2c) .Looking on UCSM at the profiles and corresponding blade, the NICs show vmnic0 to 3 as designed (I am assigning 4 NICs).Once vSphere gets installed (I am using Vmware Autodeploy), ...

Just a heads up - Java 7 Update 45 has problems and breaks UCSM launching successfully.You may see one of two errors:Login Error: java.io.IOException: Invalid Http responseLogin Error: java.io.IOException: Server returned HTTP response code: 400 for ...

Hey guys, today I want to start a little discussion about monitoring of uplinks and interpreting the results of the report.In my UCS Central, I created a report for all my four FC uplinks FI-A:31-32 and FI-B:31-32 of my UCS. (see report in attached f...

How can I see what service profile is using what IQN in UCS Central?  All it shows is Assigned-to-Single.  Thank you 

Very strange effect:Firmware server autoinstall from 2.0.4b to 2.1.3fI created a host firmware package, and then I found, that the board controller asks for a further reset ?? see screen shotsI thought that HFP does Bios, CIMC,.... all in one step.Be...

Hi all,i have 2 ucs c460, 1st ucs i can boot into webios to create raidthe other 1, pressing ctrl+h , still cant boot into webioswhen i check bios at boot options, there is no pci raid adapter detected, only cdrom,network card and efi shellbut at cim...

Hello,I have built a Windows 2012R2 Hyper-V cluster on B200M3's 2.21d firmware VIC 1240. I was unable to get the OS to enable VMQ on the NIC's that I presented to Hyper-V for VM networking. I finally found that I needed to create a  VMQ Connection po...

Hello all,I would like to know how to check the "overall state" of the UCS C220 M3 rackmount server.I have searched and walked through a lot of OID, but I can't find which one is the "Overall Server Status" for example ?The goal is to poll the main i...

Welcome to the Cisco Support Community Ask the Expert conversation. Learn and ask questions about Cisco Unified Computing System (Cisco UCS) Central.Starts November 7th, through 21stAs organizations scale their Cisco UCS infrastructure, managing it c...

We have a senerio with some of our UCS domains.  when we add a new storage array some paths will login to the array but not all will login until we reboot a host.  We have 4 UCS domains 6140x, 6248 and 2 x 6296.  the older 6140 seems to always login ...