Do you have any information about the licensing for the ports for N5596?
Do you have any information about the licensing for the ports for N5596?
As my another discussion suggested, I have VIC 1240 and 1280 adapters installed on the B200 M3 blade.Automatically UCS will create 4x20G port-channels between the adapter and the blades. So we have 80 G total b/w to the FI from the blade. 40 G to sid...
dear experts;I meet a problem.I creat two vhbas in my B200M3 server .one of my vhbas cannot fcping in the SAN switch(the other vhba is normal ),however SAN switch can see it(show npv status in FI is normal,VIF path is up),just cannot fcping,and we ca...
HiI have this issue that I got the error code F0864.I have read that the workaround is to unplug the IO module and plug it in again and then do an reset (reboot) of the IO module!?I wonder if I can do this without any interrupt to the environment ?I ...
The combination B230-M1,ESXi5.1,UCSM 2.1.2a is not certified.The combination B230-M1,ESXi5.1,UCSM 2.0.5 is.Q. can I run Infrastructure at 2.1.2a, and the B230-M1 blade with a HF of 2.0.5, and the remaining M3 blades with HF 2.1.2a ?
Hello,I am trying to find the newer VM-FEX tools as well as the VM-FEX Hyper-V extension that is compatible with UCS 2.1(2a) and Microsoft Server 2012.The guides point to http://developer.cisco.com/web/unifiedcomputing/vmfex/resources which only has ...
i am looking at the port channels configured on the FI. And this is it. port channel 21 is (eth 1/27-20) which is connected to the nexus 7000so what are the rest? (nxos)# sh port-channel summary Flags: D - Down P - Up in port-channel (members...
Hi team,Have to quickly configure the UCS to provide 80G link from B200 M3 blades to FI.I have two adpaters: 1 VIC 1240 (VIC1240 is in the mLOM slot), 1 VIC 1280 and IOM module is 2208xp. After tchecked the doc, I found the solution as attached. But ...
We just bought and installed some B200 M3's. We also purchased the SD Cards so that we could install ESXi on them. We cannot see how to get the SD Cards to show up as a Local Disk option in the M3 servers...Any help would be appreciated.David
hi:I am new in UCS. Need to implement a UCS project and I have read quite a bit, but really need someone with hands-on experience to vet through the following:BOM - 1 unit of UCS 6120XP, 1 unit of UCS 2104XP, 1 unit of UCS 5108 chassis, 2 unit of UCS...
Dear Team,We were trying to create port channel between UCS FI and MDS 9124 But the port channel not getting active in F mode on MDS 9124 FI is in FC End Host Mode We have enabled FC uplink trunking on FIWe have enabled NPIV on MDSWe have enabled...
Dear Team,Need some insight on UCS and Nexus 1000v Infra setup with VMWarehere is where we standWe have decided to create Service Profiles which will have6 vNICs and 2 vHBAsvNIC1-Mgmt FI-A- VLAN 100vNIC2-Mgmt FI-B- VLAN 100vNIC3-Data FI-AvNIC4-Data F...
Just got my hands on a few C240 M3′s with the VIC 1225 adapter and began setting them up as a VMware 5.1 U1 cluster. I’ve configured 8 vNICs per host: 2 for Management, 2 for VMotion, 2 for iSCSI, and 2 for VM traffic. Each pair of vNICs has one pinn...
I am trying to obtain the list of Server Ports that have been enabled on the FI-s using PowertoolI am using the below command and I am not getting nadaGet-UcsFabricServerCloud -Id "A" | Get-UcsServerPort -AdminState "enabled"Have tried without any a...
I can obtain the speed of the Network Uplinks on the Cisco FI-s using the commandGet-UcsFiLanCloud -Id "A" | Get-UcsUplinkPort -AdminState "enabled" | Foreach-Object { $_.adminspeed }However, there is no option to obtain the negotiated speed of the F...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-11-2025 03:18 PM | ||
05-21-2025 07:35 AM | ||
05-07-2025 03:02 AM | ||
05-07-2025 12:11 AM | ||
04-30-2025 01:15 AM |