I have deployed two 1010 appliances, the upstream switches are two 6509 wihtout VSS.I cannot get the HA up.Output of show module is:Mod Ports Module-Type Model Status--- ----- -------------------------------- ...
Unified Computing System Discussions
Engage with peers and experts on UCS and HyperFlex topics.
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- Technology and Support
- Data Center and Cloud
- Unified Computing System (UCS)
- Unified Computing System Discussions
Options
- Mark all as New
- Mark all as Read
- Float this item to the top
- Subscribe
- Bookmark
- Subscribe to RSS Feed
- Threaded format
- Linear Format
- Sort by Topic Start Date
Labels
-
Buying Recommendation
(18) -
Call Control
(1) -
Cisco ACI
(2) -
Cisco Bugs
(5) -
Cisco Cafe
(5) -
Cisco Intersight
(1) -
Cisco Software
(1) -
Cisco.com Idea Center
(1) -
Collaboration Endpoints
(1) -
Collaboration Solutions
(2) -
Community Feedback Forum
(6) -
Community Ideas
(5) -
Conferencing
(1) -
CSC Content with No Valid Community to Post
(1) -
CUCM
(1) -
Data center
(2) -
Data Center Networking
(1) -
Hyperflex
(145) -
Identity Services Engine (ISE)
(2) -
ISR 4000 Series
(1) -
LAN
(1) -
LAN Switching
(3) -
Network Management
(2) -
Online Chat Support
(1) -
Optical Networking
(1) -
Other
(1) -
Other Collaboration Applications
(7) -
Other Collaboration Topics
(4) -
Other IP Telephony
(2) -
Other Networking
(1) -
Other Switches
(2) -
Other Switching
(4) -
Other Unified Communications
(13) -
Other Unified Computing System
(709) -
Routing
(1) -
Server Networking
(1) -
Small Business Network and Smart Storage
(1) -
Small Business Routers
(1) -
Small Business Support Service
(1) -
Storage Networking
(1) -
Switching
(1) -
UC Applications
(8) -
UC Management-Licensing
(1) -
UC Migration
(1) -
UCS Advantage Series
(9) -
UCS Central
(67) -
UCS Director
(19) -
UCS Manager
(409) -
UCS Networking and Storage
(197) -
UCS PowerTool
(48) -
UCS Solutions
(162) -
Unified Communications
(18) -
Unified Computing
(2) -
Unified Computing System (UCS)
(6,620) -
VDI
(3) -
Voice Gateways
(1) -
Wireless LAN Controller
(1)
- « Previous
- Next »
Forum Posts
Hi,Currently the UCS FIs are connected diretly to EMC storage using FC expansion module (FC Switch mode)I need to migrate these FC uplinks to N5K which will be connected to the storage (without down time).Is this possible?I have two FIs, can I discon...
Hello,In the PERFORMANCE tab in Fabric Interconnects (EQUIPMENT general tab in UCS Manager) one can see several columns, like %Utilization.What does the "%Utilization Tx" mean in a vNIC, whether it is the %Utilization regarding the physical port spee...
I have a C200 M2 server running ESXi that has some hardware issues. I have a new replacement C200 M2 and will need to transfer the old CPU, RAM, and harddrives to the new server.My question is, will I be able to boot up off the old harddrives in the...
I am planning to deploy UCS in the next month or so. It sounds like each UCS chassis requires four L6-20 receptacles.And we're getting two chassis. So I was looking to get a couple of Pulizzi like the onces below. Anyone prefer anothertype for bet...
Resolved! Cisco ucs with VMware 5 auto deploy
Hi,In our lab i am testing with VMware 5 and Cisco UCS. We are running UCSM 2.0 (1m). I am now testing the part auto deploy. I have setup auto deploy in VMware and it is working ( first i had some issues with DHCP on windows that is solved in the UCS...
Anybody know these? Craig
I have the typical setup:2 x 6248 Interconnects2 x Brocade SAN SwitchesEMC StorageAll cross connected for redundancy. However, I am not seeing any logins to the second SAN switch when I boot a blade. I looked at all the vSAN config's etc., and it loo...
Hello all,I'm having a problem creating a Raid 1 on my ucs c210 m2 in order to install esxi with redundancy, I installed the mezzanine card to support raid 1 with esxi, but i can't see my sata hard drives when i go to the lsi setup. Can anyone help m...
Resolved! Configuring UCS FC Uplinks
Hi,I am confused about configuring the UCS FC Uplinks.the setup is as follows UCS (2 fabric Interconnects - 2 different VSANS) --> Nexus 5k (2 for redundancy - each FI to a Nexus) --> EMC StorageI have connected 2 FC ports from the Fabric Interconnec...
I was trying to understand the description in the picture below.Question #1: Are the part numbers below is for a single piece of memory stick? Or it could be multiple pieces?Question #2: If they are for a single piece, why 8GB would have the same pr...
Hi All,First i'm new to UCS so excuse my lack of knowledge. I had some questions about ISCSI and NFS traffic over 10GB ethernet.We are planning on having 5548's and two 6248's interconnects, when does it make sense to use the 5548's forour ISCSI SAN...
Hi guys,I am planning to install UC applications on couple UCS C210M2 servers and i need to know where to start from and what needs to be setup first like configure the management port , CIMC, upgrade firmwares, install esxi, license files for vmware...
Hello,After installing firmware 2.0(1t) I got the gollowing error when booting up the blades in the General - Status Details:"Missing or Incompatible BIOS Image"Has anyone experienced this, if so what is the fix?Thanks
Is it possible to just walk up to blade with keyboard and mouse, CD drive to install OS?
Learn, share, save
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Unanswered Topics
| Subject | Author | Posted |
|---|---|---|
| 12-03-2025 07:07 AM | ||
| 11-30-2025 06:22 PM | ||
| 09-23-2025 12:33 PM | ||
| 09-09-2025 06:54 AM | ||
| 09-05-2025 12:03 PM |
New solutions
