I have a C200 M2 server with BCM5709 ethernet card, I am trying to find the drivers to load windows server 2008 R2. I am trying to install to an iSCSI SAN, the LUNS and volumes are all configured as they were just running VMWare, the iSCSI boot i...
We have 11 digit DN's. Users are used to dialing and see'ing 6 digits. I have used transformation patterns so that when someone is called, the person called see's the call as just the last 6 digits. However, the person who dialed 6 digits sees the en...
hi team,in the latest UCS hardware and software interoperability matrix, we can see 1.4.3 begin to support vmware version 5 as well.But in the interoperability matrix, vmware vsphere 5 is only support on B440M1.Does Cisco has any plan to support vmwa...
Hi All,Just a simple Q.I got a 2 unit of UCS in my infra.I need to change the IP address from Private IP Address to Public IP Address.From what I see, I need to change below IP Address.1. Management Interface IP Address & Cluster IP address2. Managem...
Hi,I have seen a problem where in some virtual ethernet interfaces get binded with multiple physical interface and can not be seperatedinterface Vethernet100 switchport mode trunk bind interface Ethernet1/15 channel 2 bind interface Ethernet1/20 c...
I have been working on some scripts to configure a number of vlans on a UCS environment. In the end I had configured the same vlan (hr) onthe A fabric fabric/lan/A/hrthe B fabric fabric/lan/B/hron both fabric fabric/lan/hrSo I have three objects wher...
HiWe purchased a C210 M2 server from a local web store that is not a Cisco reseller, just sell all kind of electronics.The server has 16 disk trays and the next step is to buy SATA hard drives but ..The disk trays/enclosures look to be designed for a...
I know this is more of a Cisco MDS/Storage question, but does anyone know out of LUN Masking and Zoning, which one would be the most prefered method ? I have two Cisco 9148 Fabric switches, two Netapp FAS3210 SAN Controllers, 1 UCS Chassis with 4 B20...
Hi Folks,Can I attend the UCS Design course before getting the VCP ? I will achieve the VCP later on, and I do not mind to have the UCS certificate later on.Regards,Ismail
Hi All,This is one basic question. If any UCS user can kidly help me by providing a check list for the configuring a server port in the UCS, I will be greatful.What i did was turn a port as server port using the UCS manager and i did nothing more. Th...
Hello,I have 2 UCS with 2 pair of Fiber interconnect 6120XP and they are conencted to Nexus 5k. Currently 10Gig Ethernet and FC are used for connectvity. I have 8 port FC module in Nexus 5k. Storage is connected to Nexus 5k over FC. I would like to c...
I upgraded to UCSM2.0 over the weekend, and now UCSM won't load, due to a certificate error. I am a MAC user and this worked with 1.4.x but now with 2.0 it doesn't. If I load my WIndows 7 instance everything is fine. Very annoying but just wanted ...
Hi All,Could you please help me clarify the followingReferred document:http://www.guug.de/lokal/berlin/GUUG%20Nexus%2020100805%20chbock.pdfThe page 41 of the above cisco document describes the implementation options of VN-Link.According to that, HW V...
Anyone have a source or disk cradles for the UCS 210 ? I have access to disks easily enough but there seems to be no supply of the cradles.Even finding cradles with disks is hard.Any pointers ?Anyone know anyone who could make up custom stuff if I c...
