01-29-2017 09:38 AM - edited 03-01-2019 01:03 PM
I'm working on DC/Sec technologies. would you mind, please confirming me on this?
Solved! Go to Solution.
02-02-2017 06:17 AM
Greetings.
Unless you are using VM-Fex (for ethernet) , or vHBAs at the guest VM level(this is only supported on hyper-V currently), the vnics and vhbas defined at the service profile level are obscured at the hypervisor level, and the storage seen by the VMware guest VM is just a .VMDK file parked on a datastore the ESXi host has mounted.
Your upstream device configuration/capabilities will determine whether you setup FCOE or FC uplinks on the FIs.
Thanks,
Kirk...
02-01-2017 12:09 PM
Please see http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/ucs-manager/Reference-Docs/Configuration-Limits/3-1/b_UCS_Configuration_Limits_3_1.html#reference_6A3C0158393549E5A3E3F87002234145 for vnic/vhba maximums.
These are actually governed by the OS limitiations. You hit the OS limitiations long before you get close the the UCSM/hardware limits.
If you are going to attach FC/FCOE storage processors directly to the FIs then you will need FC switching mode as that will allow you to do the required local zoning.
If you intend to connect to FC/FCOE storage that is northbound, then you will want to setup the appropriate FC/FCOE uplinks, along with the corresponding VSAN and underlying FCOE vlan.
You will reference the vsan on the vHBA in the service profile, and on the FC uplinks.
Connecting Non Cisco servers to the FIs is not supported. Exception is an appliance storage port > IP storage such as NFS or iSCSI
Thanks,
Kirk...
02-02-2017 12:42 AM
Hi and thanks for your reply. It's better to ask my question in a very simple way; supposing I'm going to install ESXi on a b-series server, is it possible to configure FCoE on that ESXi server, so that server uses FCoE on it to connect to both Lan/San networks?
02-02-2017 04:00 AM
Greetings.
While FCOE is the transport used within the UCSM, the bare-metal OSs simply see a regular FC HBA, and you do not need to configure FCOE at the OS level.
If your FIs have native FC ports connecting to upstream SAN switches then the Ethernet encapsulation is removed and the FC frames continue northbound.
It's the flexibility of the VIC adapters & service profiles that allow you to create both Ethernet and FC hbas that are presented to the PCI bus of the Host.
Thanks,
Kirk...
02-02-2017 04:41 AM
Thanks a lot Kirk. based on what I understood from your comment, the bare-metal OSs and even VMs inside that bare-metal OS just use vNIC (for ethernet) and vHBA (for SAN), then traffic handled "internally" and "automatically" by UCS up to the FI without our interactions (regarding to the FCoE). Only from that point up to the network core is where we can use either of native FC/Ethernet or FCoE. would you confirm me on this? tnx again.
02-02-2017 06:17 AM
Greetings.
Unless you are using VM-Fex (for ethernet) , or vHBAs at the guest VM level(this is only supported on hyper-V currently), the vnics and vhbas defined at the service profile level are obscured at the hypervisor level, and the storage seen by the VMware guest VM is just a .VMDK file parked on a datastore the ESXi host has mounted.
Your upstream device configuration/capabilities will determine whether you setup FCOE or FC uplinks on the FIs.
Thanks,
Kirk...
02-02-2017 01:18 AM
so if we assign this service profile to this B-series server, does it mean that this server just has 4 LAN interface and uses them to connect to the rest of the network plus 2 of HBA card to connect to the SAN?
Yes.
does it mean that we now have 256-6=250 VIC remaining ready to be assigned to the VMs that will be created on the same B-series server in the future?
No. You assign to the VMs virtual ports of vSphere virtual switch.
does that mean traffic of all of the VMS that will be created on the same B-series server eventually have to exit off the same physical B-series server through 4*vNIC interfaces that were created before as result of service profile?
Yes. If all of vNICs assigned to the same virtual switch. But you may create 2 virtual switchs with 2 uplink each.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide