cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1066
Views
20
Helpful
6
Replies
Highlighted
Beginner

Associate error - "Server features are not compatible with UCS underneath"

Hi all,

I'm trying to associate a GSP with a UCS domain but getting the following error. On the General tab:

There are not enough resources overall.
ucs domain does not have the matching server capabilities for this service-profile.

And on the Status tab:

Stage descriptor: Analyzing changes impact(FSM-STAGE:sam:dme:LsServerConfigure:AnalyzeImpact)

Tries: 0

Previous state: ConfigureFail

Remote Err Code: 5

Remote Err Description: Server features are not compatible with UCS underneath.

Remote Inv Result: resource-unavailable

The UCS domain I'm associating this GSP with is an existing domain I've just registered with UCS Central. I have successfully created and associated a GSP with a greenfield UCS domain in another datacentre.

Both domains are running UCSM 2.2(6d). UCS Central is 1.4(1a).

I found a bug which suggests this might be due to the presence of a Boot Policy, but the workaround (remove the boot policy) does not work in this case.

So, does anyone know what could be going on here?

Thanks

Richard

Everyone's tags (1)
1 ACCEPTED SOLUTION

Accepted Solutions
yok Cisco Employee
Cisco Employee

Richard, 

Richard, 

Please check the following bug: CSCuy07572

You can use the global default and should work completely fine.

You can choose the required version over here.

Non default policy will have an issue.

Thanks, 

Yoga

View solution in original post

6 REPLIES 6
Highlighted
Beginner

I have resolved this to my

I have resolved this to my dissatisfaction by removing the host f/w pack I created. The profile is now associating.

Which begs the question, how do I properly create a host f/w pack and upgrade the f/w on the blade? It works quite differently to how I'm used to doing it in UCSM.

Highlighted
Cisco Employee

Hi Richard,

Hi Richard,

I'm glad you solved it. This is a really good guide that gives you step by step instructions on how to do this within UCS Central.

http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/firmware-mgmt/gui/2-2/b_GUI_Firmware_Management_22/b_GUI_Firmware_Management_22_chapter_01101.pdf

Regards,

Highlighted
Beginner

Qiese,

Qiese,

Thanks for the guide. Unfortunately it's not quite accurate and I'm still stuck on three things:

1) I followed the steps for "Creating a Host Firmware Package" successfully. But on "Deploying a Host Firmware Package", in Step 4, nothing shows up. Tried a different browser (Chrome and IE).

2) Even if it does show up, this looks like it will start upgrading ALL the blades in the UCS Domains, which is not desirable.

3) If I simply proceed to select Install Servers, there are no Impacted Endpoints. I have chosen my FW policy in the GSP "Policies" section. If I look through UCSM, the GSP Policies tab for Firmware Policies remains on "Select (default policy used by default)".

Cheers

Richard

Highlighted
Beginner

Hi Qiese

Hi Qiese

Do you have any update on this please?

Thanks

Richard

yok Cisco Employee
Cisco Employee

Richard, 

Richard, 

Please check the following bug: CSCuy07572

You can use the global default and should work completely fine.

You can choose the required version over here.

Non default policy will have an issue.

Thanks, 

Yoga

View solution in original post

Highlighted
Cisco Employee

Hi Richard,

Hi Richard,

So I see you saw the Boot Policy bug but since you removed it the error still persists. Is this service profile apart of a server pool? If the blade you are trying to associate is not in that pool then this error would possible occur.

Can you also try to create a new service profile without the boot policy and see if that will associate.

Regards,

Qiese Dides

CreatePlease to create content