Hi All, I have two questions:I have two FI-6454, each with two FC uplinks,1. As far as I know, a vHBA of a UCS Blade map to an FC uplink?2. If I want to setup the current two FC Uplinks into port channels, will it cause a disconnection? Thanks.
Greetings, thanks for reading. I have NetApp storage attached to Nexus 5k for the FCoE zoning and SAN boot and then to ACI.We simply removed those connections to the 5k and instead directly attached to the Fabric Interconnects and went from twinax to...
Howdy Folks, Can anyone confirm if the UCS-FI-6454 can support a copper 10GBASE-T SFP+ module, specifically the SFP-10G-T-X? So far, all I've check the optics compatibility matrix and the 6400 spec-sheet and I see no mention of this module being supp...
Greetings,We have a situation where the modules of our FI are offline, however the fixed modules are working as expected:Mod Ports Module-Type Model Status --- ----- --------------------------------- -----------...
All, We have deployed many VMware vSphere / vSAN clusters over the years on UCS M5 and M6 hardware. In those cases, the Cisco HBAs were always on the VMware vSAN HCL. In the case of the UCS M7 series, the only HBA available is the UCSC-SAS-T-D, and...
I am told that the UCS-M2-HWRAID only supports RAID1 and JBOD.I have a single SSD, so I would like to configure as a JBOD.The documentation to configure RAID1 on the UCS-M2-HWRAID appears to be straight-forward.However, I can't find documentation for...
We're trying to upgrade our 6248UP FIs to 6454s. There are no errors on any FIs/IOMs/servers. However, when we try to evacuate the subordinate FI, we lose all network traffic to the servers and the VMs. We do not lose access to UCSM and cluster lead ...
I am in the process of migrating my lab from M4 to M5 servers, and I have hit a snag. The problem is with my main NAS which is running TrueNAS 13.0. As part of the upgrade I ordered Western Digital 2TB WD Red SA500 NAS drives to replace the SATA HDD'...
Have a customer that wants to connect their NetApp AFF150 to their 6300. The NetApp only supports 10GbE, is it possible to use a CVR-QSFP-SFP10G adapter on the FI side and set the port to 10GbE and it function ok? Having a hard time finding clear ...
Good day, I'm having an issue where the UCS S3260 will not allow me to create a VD from the Storage configuration on the CIMC I have tried assigning the Disks to the correct Zoning policy in multiple ways and every time I go to the Storage > Raid Co...
Hello Experts, I am searching aboout cisco Fabric interconnect to UCS server, I am wondering how can Cisco FI discovery UCS Server ? Can you help share some explanation ? Thanks in advance !
Have iSCSI Boot configured on UCS on code level 4.1(3).UCS-FI-6248UP FI's and M5 Blades.iSCSI Boot is working, but is SLOW. After server is booted the speed is what would be expected.10g to the NAS controllers. Not using Appliance Ports.
Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Are you already familiar with the new Cisco UCS solutions and the Cisco Intersight™ infrastructure management platform? The Cisco Intersight Infrastructure Service is...
Hello I was recently given a ucs C240 m3 sff server and was wondering if the front drive carriage assembly could be swapped out to convert it to lff? I have plenty of spare 3.5in drives and would really really like to not have to spend a ton of money...
I have a new UCSC-C220-M5SX configured in my lab loaded with Esxi, 2 Socket 512GB RAM. Even though utilization is below 25%, FAN makes loud noise. Fan policies are correctly set, logs are clean, tried upgrading firmware to 4.2(3g) ,so far not much o...
