We have 3 standalone C240-M4SX rack servers, running on Windows Server 2016 with Hyper-V installed. I am unable to get SR-IOV working on VIC1227. We have latest firmware installed (from huu 4.0.1b) and latest VIC drivers (4.0.0.3 dated 04.01.2017) SR...
Forum Posts
I'be been banging my head on this for a while now. I've attempted all of the other solutions I've found here. Basically, I'm trying to get the server to boot ESXi off of virtual disk 0. This is what I've done so far: Booted into WebGUI for the LSI ...
Hi everone, i am new to hyperflex, i did my first deployment two days ago using the latest HX installer 3.01e and ucs version 3.2.3h and the same for B & C series and vcenter 6.5 U2. i didn't upgrade the ESXI version before cluster creation so it i...
Hi All, Our org is quite new to UCS mini. We are having a weird issue with some of our Esxi servers on B200 M4 blades dropping the Esxi management network for a minute or so periodically daily (Every other network is ok) and I think it may be down ...
I tried searching but I cannot find a clear answer on this. Can the UCS mini be converted from the 6324 IOM's to a 6332 via an online process? or can the config be backed up, the IOM's replaced, and then configs restored to a 6332?
I am looking to upgrade from 6148 to 6332-16UP Fabric Interconnects. I would like some info on steps to do this as I've never installed one. Thanks, Scott.....
Hi We are planning to upgrade UCS firmware from 3.1.3c to latest stable 4.0.1b (starred). We checked the compatibility for Windows 2016 & ESXi 6.7 and found it's compatible. The drivers that we run with the servers are 3.2.1b. Our concern is shall ...
Hello Everyone ! I need some help as i can't access the UCS Manager 3.2(3g) from either of the browsers - IE11, Firefox62X, Edge or chrome - I've modified the JAVA Network Setting to Direct Connection even added the IP of the UCS Manager to the Exce...
Hi,I am trying to install Hyper Flex with 3 nodes and use the nested v Center setup. Initially I used v3.0.1e then I was about to connect to Hyper Flex connect for v Centersetup but it prompt me an error that no cluster was created, so I redo again f...
Good morning, all! I have some C210 M2 servers that I have to update to ESXi 6.0 U3. The recommended BIOS level from the VMware HCL is 1.4(3m) or 1.4(3n). The current BIOS rev is 1.4(3l) - that's L as in Larry. The HUU download doesn't list the 1.4(...
I have a S3260 chassis with one server and one SIOC. Creating a service profile for the S3260M4 server with only network NIC's is no problem but as soon as I configure FC HBA's in it comes out with configuration-failure due to insufficient resources....
We are looking at adding additional connections between our UCS 6248UPs and our catalyst CS3850s. Currently we have the following FI-A to primary cs3850 FI-B to secondary cs3850 We would like to add FI-A to secondary cs3850 FI-B to primary cs3850 ...
Hello, we have several UCS domains (all Cisco UCS 6248UP) in different DataCenters and we need now more Port Licenses in one of the DataCenters. In one of the other UCS domains, we have two Cisco UCS 6248UP with the Expansion Module UCS-FI-E16UP in...
Resolved! Question about building a C240 M5 Server
Good Morning, We have just recently changed hardware providers going to Cisco servers from HP. I have been tasked with configuring a C240 M5 server for Windows 2016. This is my first time building a Cisco server and I seem to be running into a c...
Question on VMQ/SRIOV with Hyper V 2016 on Cisco UCS (6248UP FI / 2204XP IOM/ B200M4 blade/1340 VIC)
Hi We are migrating from 2012 R2 HV on another blade solution to 2016 HV with Cisco UCS and both are new to us. We found very interesting and helpful forum on Hyper V (2012 R2) on UCS (https://social.technet.microsoft.com/Forums/en-US/24f8dd51-07db-4...
