Dear Folks I need to add new vlan in global vnic service profile template. Created new vlan and published in UCS domain.If i add the VLAN in vnic template whether it will affect the baldes which is running already ? Regards Dinesh.J
One of my B200 has a bad motherboard, it runs Windows 2008 Std installed on a RAID1. I want to swap out hardware by changing the server profile and move the HDD to another B200 blade. So my plan is: 1. Turn off the malfunction B200 2. Unmount the S...
Dear All, To our network infrastructure we have 2 different stack switches 3750 (Stack1 & Stack2) and a UCS 6248UP with UCS Manager 2.2(3f) which connects to Both stack switches with port-channer and DJL2 enabled. More Specific For Port-channel conne...
Hi,I have a cisco c220 M3 server . I was change access WebUI port http and https. I did the same http and https. Now Not access.How can I access?
I have problem with hard drives in my blade. The faults say: Firmware Detected Drive Fault I replace the HDD with another but I got the same error message. Every HDD that I replaced with these got the same error and amber light. On front side of my ...
Hello, we have a test UCS environment that connects to to Nexus 5k upstream. Today as practice for learning UCSM, I configured a new VLAN under LAN tab. Once creating this VLAN, we lost connectivity to all our virtual servers in the blades. THe on...
I am looking for information on what "operability" means with regard to CPU State. (See attached Screen shot). I have a server that shows it at N/A. Cisco TAC has reviewed the logs from the server and have found no issue. The overall status is ope...
Hi All , I want to update Cisco Nexus from n3500-uk9.6.0.2.A4.4.bin to n3500-uk9.6.0.2.A6.5a.bin , but am facing threshold error. Please guide me what are the possibilit for it. I have free space but facing error. # dir bootflash:/// ...
Running SCOM 2012 R2 with the 4.1 UCS management pack, discovered and monitoring the central UCS fine, we have 28 remote IMC's we are trying to monitor, when added in pairs either one of both fail with login error and SCOM stops monitoring them, i ha...
we are planning for a firmware upgrade on our UCS environment. Currently its running on 2.2(3c) and planning to upgrade it to 2.2(8). SO my question is can we apply the upgrade on a particular chassis or a blade server that we want to run on 2.2(8).T...
I am trying to create a framework for Powershell access to the HX API. I cannot seem to get past authentication. PowerShell is preferred, because follow-on actions are going to be in PowerCLI. Basically looking to obtain a list of nodes. Put each no...
I want to get the CIMC & BIOS settings and compare it across a large number of servers. I can get the BIOS data with ucscfg which is fine. However getting CIMC data seems impossible. Realistically I am looking for Networking and Storage primarily. W...
Hey all, I'm deploying a new HX cluster and hitting this error on all of my nodes. (IPs change per node respectively) ESXi reachability check IP address: 172.20.7.22 at default port: 902 is not reachable. This is all internal and not going out ...
How do I rename objects in UCSM - things like service profiles,templates, policies, etc. I can't find anything in the GUI or CLI to do this.Thanks.
Hello, is any of you who may suggest a list of HW HDD supported by ACS-1121? from, data sheet it says HDD 250 GB 7.2K RPM 3.5 inch. Any HDD brand is good, or there is a list of matrix compatibility? thanks https://www.cisco.com/c/en/us/products/c...
