Unified Computing System Discussions

UCS C240-M3S CIMC upgrade fail

Dear Sirs, I have one UCS C240-M3S Server. Because I can't open the kvm console with java, I decide to upgrade the firmware with CIMC.When I upgraded the CIMC and upload the firmware , my notebook computer crashed.The result is that UCS is very slow ...

UCS Central shows 'Major faults' but UCSM does not

Hi, For some reason, UCS Central is showing 7 major domain faults, all of which are like this: Firstly, this doesn't even show *which* domain the error is in, but thankfully we only have two. Logging into UCS Manager for both domains, there are *no...

Resolved! TCA: etherNiErrStats crcDelta

We recently upgraded our UCS Cluster from 2.2(3f) to 2.2(6e). I didn't use the auto upgrade, i used set of directions provided to me by TAC. Since the upgrade, Both of my IOM (2208XP's) throw the following errors: sys/chassis-1/slot-2/fabric/port-4/...

UCS C240 M4S2 fans spinnig too fast

Hello Experts, We have 3 UCS M4S2 servers (ordered as BE 7000 Bundle).Version: 2.0(6d)The servers have been running (without any load - just OS ESX 5.5 without VMs) for about one month without any problems.After 1 month, fans in one server started sp...

Cisco UCS C210 M2 Server

Hi all, I have a c210 with ESXI 4.x the issue is my hdd are crashing almost 1 time a month, I changed my controller and still the same issue. The bios version is C200.1.4.3l.0. Thanks all. 287

Resolved! Best practice guidelines for Ucs manager to run smoothly our environment

Hi Team We are maintaing data center with Cisco Ucs blades.I want best practice Ucs manager guide for Ucs manager to verify all the things properly configured as per the Cisco recommendation and standard to run the environment smoothly.Kindly some on...

DependencyError on fnic_driver_1.6.0.25-offline_bundle-3741467.zip" [

I am getting the following dependency error when updating the driver on a esxi 5.5 host. firmware version is 2.2(5) according to the compatibility matrix, esxi 5.5 needs t be updated to 1.6.0.25 on the fnic /vmfs/volumes/548c8b67-1c427a73-66c2-002...

Blades are failing to discover

Hi everyone, I purchased two new B200-M3 blades and they are failing to discover when I'm downgrading the firmware on them. It came with a 3.1(1e) package and I'm trying to downgrade to my infrastructure at 2.1(1a).

CMA

what is the diffrence between cable managment arm and KVM ?

Is it good to have few Chassis with 2204 IOM and few others with 2208 IOM? Is it supported configuration?

UCS Infrastructure consist of following: Chassis - 5108FI - 6248UPIOM- 2204 and 2208

VMQ configuration

Can someone point me into some definitive VMQ configuration documentation that is specific to UCS? I'm trying to set VMQs on 4 vNics but every time I reboot the profile, some of the VIF paths come up and some don't depending on the configuration of ...

Resolved! Connection between FEX and FI

Hi,We have the following setup,UCS-C <> N2K <> FI-6248 <> N9KIs the connection between FEX (N2K) and FI (FI-6248) must be an MMF cable, could we use single mode SFP+?I found below Cisco DOC about the uplinks connection from FEX to FI could only use t...

Resolved! Connect-UCS with the help of the XML file

Hello all experts,I am trying to connect to a UCS manager using the credentials saved in a XML file. Here is how I am doing it :-1. Connect-Ucs -Name <Name>2. Export-UcsPSSession -LiteralPath c:\test.xml ( Specified the key as "ucssession" when it pr...

Resolved! UCS-SPL-5108-AC2 // UCS-SPM-5108-AC2 - Code Change

Hi, I was looking for the Chasis 5108 bundle, we previously acquired the following P/N (UCS-SPL-5108-AC2). I have seen that the P/N has change to UCS-SPM-5108-AC2; but i want to be sure that the configuration inside is the same as the old P/N. Thank...

Nexus 9K.

I am looking for specific documentation related to the Nexus 9K (9396) and it's hardware ASIC layout per line card/module, does anyone have any information related to this topic to pass along? Thanks, Mark S.