"UCS-FI: reload or switchover may occur due to Leap second update"http://www.cisco.com/web/about/doing_business/leap-second.htmlUCS: https://tools.cisco.com/bugsearch/bug/CSCus83447 Affected versions:2.2(1b)A2.2(2c)A2.2(3a)A
"UCS-FI: reload or switchover may occur due to Leap second update"http://www.cisco.com/web/about/doing_business/leap-second.htmlUCS: https://tools.cisco.com/bugsearch/bug/CSCus83447 Affected versions:2.2(1b)A2.2(2c)A2.2(3a)A
Hi ,I dont have good knowledge on nexus 5000 , but after going through lot of doc I am trying to setup UCS with nexus 5000 and san storage.My objective is to boot server from san storage. My setup :-------- UCS------>Nexus5000---------SAN storage As ...
Dear community, just fyiI just run at a customer site in the following issue: New chassis with 4 new B200-M4 and local 300GB SAS Toshiba disks, firmware 2.2.3d.SP association failed, error message : Raid controller L2/L3 cache failure,.... see attach...
HiHow could I format the local HDD of UCS blade server B200M4 using UCSM ?I heard some body said that we can do that using scrub policy and the RAID type to no RAID, I could not accept that but I tried and failedthanks
HelloI just configured boot from SAN and installed my first OS (windows 2012 R2). Now that the OS is installed I am starting to have network issues. One thing I have noticed is that the event log says that both ISCSI nics are configure for DCHP and...
Hi,I have been encountering an issue while creating a virtual drive out of two HDDs and configuring RAID on them.I hope, i can continue to create VD over CLI than GUI with no errors. But, is this something i need to worry about?I couldn't find much i...
New customer install has issues with single blade. After running a few days we powered down all devices, upon powering back on 1 server wouldn't boot. B200 M4 2.2(5A) Booting from SAN, no changes done to it all others are identical and powered u...
Hello EveryoneThis is kind of a high level question and wanted to know peoples opinions on how to setup networking. Currently we have a few clusters running on 6 1 x GB links and use converged networking to team all nics together and use VMM logical...
Hello, Experts.This is Jungwo Hong from e-tech system in Korea.My customer had some difficulties about installing RHEL 6.6 (RedHat Enterprise Linux) on their system - C240 M4 They want to install their OS to the disk drives bundled with RAID level 1 ...
I have a UCS B200 blade/chassis with Cisco Virtual Interface Card 1240. I cannot for the life of me get NPIV to work. I can't find any configuration documents for this setup and the only post on here I found is from 2 years ago and says that Cisco me...
I have seen recently that during firmware upgrades the virtual IP does not failover to the surviving fabric interconnect within the expected time of 30 seconds to 1 minute. I'm referring to the mgmt0 interfaces of the UCS FI's and the VIP and the man...
Good afternoon! We had a brief problem with a RAID 10 that holds the ESXi installation on one of our C210 M2 servers. VMware "lost" the ESXi volume. A host reboot brought the RAID back online but management had me buy a spare mezzanine card to have...
Hi, i have problem with Cisco UCS manager, after logging in UCS Manager i get an error.
After reading through numerous documents on the use of UnityConnection.OdbcSdk tools, I've found how to use the IfxDataReader to run queries, or the command tool to execute stored procedures, but nothing that can capturing the results of executed sto...
Is there something special with the internal SAS cable? LSI says I need SFF-8087 cable but doesn't appear its that simple. Thanks!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-16-2024 02:26 AM | ||
04-04-2024 11:22 AM | ||
03-18-2024 06:52 AM | ||
02-27-2024 07:34 AM | ||
02-20-2024 12:52 PM |