Hello to all,I have a problem with a Cisco C240 M4. After upgrading the firmware with HUU iso from firmware 2.0 to latest 4.1.2f controller cannot recognize any hdd.SAS expander is showing on inventory. Server has 12x300Gb 10K drives that were workin...
Forum Posts
I accidentally saved a configuration change while logged into the CIMC GUI for the NIC Properties. The NIC Mode is set to Shared LOM and I didn't notice that the NIC Interface was changed from Console to GE1 until I had already pressed the Save Chang...
Hello everyone, I need to install VIC card on Cisco blade server b200 m5. Now the issue is that once server is installed and server is reacknowledge then how/where can I know that VIC is installed. Sorry if my question seems easy/repetitive, I am bit...
Does Cisco UCS C240M5SX version 4.1 (1f) have vulnerability?
Hello everyone, I need guidance in upgrading UCS b200 m5 blade server. Right now servers are running firmware 4.0 and I need to upgrade it to 4.1 3b.Can you guys please share the steps to follow to upgrade the servers smoothly. TIA
I am wanting to be able to modify a UCS Blade to have a one-time boot boot order change so it boot from LAN rather than iSCSI. I see that on the IMC Module there is a Set-IMCOneTimeBootDevice. Is there anything like this for the UCS Blades? I have...
Hi everyone, W have Cisco UCS that we login through TACACS using Cisco ACI. This is basic and straight forward setup! I have requirement now to login through SSO as we do for some other devices using Azure SAML integration. I couldn't find any docume...
On a standalone C240 M5 server, have been able to configure Virtual Drives under 12G RAID Controller and set one of them as a Boot Drive, but cannot see controller as a boot option in BIOS or in boot menu. In BIOS, under Advanced > LOM and PCIe Slot...
Resolved! HyperFlex HX Installer VM Deleted
Hi Expert ,i have a situation , our hyperflex cluster is good , up and running ,, but we deleted the HX installer vm accidently, we need to add some vlan's now... pls help it's urgent.
Resolved! Boot device / boot media issue
Hello,HiI recently build new setup for UCS 5108 chases with 2x blade servers ( B200 M5)using two Cisco UCS 6332 16UP FI connected to Brocade SAN Switch with one Netapp af220 storage FC mode (as show in this diagram). In this setup blades boot fro...
Dearsi want to make a rebuild to raid 1 on my UCS server because this HDD will be out of warranty coverage My current configuration two HDD 1 TB RPM 7K in raid group (Raid 1)i want your opinion for the below rebuild the raid 1 with 1 HDD with 7K Spe...
I'm about to have a bunch of these RAM sticks leftover from an M4 upgrade:32GB DDR4-2133-MHz LRDIMM/PC4-17000/quad rank/x4/1.2vCan I use these in an M3 blade that has E5-2600 v2 series CPUs?The M3 spec sheet says it supports quad rank 32GB LRDIMMs of...
Resolved! c220 m3 server stuck in bios
I keep geting stuck in a loop wen setting up the c220 m3. I updated all the drivers and rebooted the server but keeps coming back here. any idea?thanks
Hi Everyone, How can I find out if the Cisco UCS B200 Rack Server is compliance with AFI 33-200, CNSSP-11, NIAP, NIST, FIPS, CMVP, and UC APL? And it is approved by the NIAP/CCEVS approved list?
Hi Everyone, Just wondering if any one knows if the Cisco UCS B200 M6 Blade Server will work with the Mellanox Infiniband 200G switches (https://www.mellanox.com/sites/default/files/doc-2020/wp-introducing-200g-hdr-infiniband-solutions.pdf). Let me k...
