Resolved! Setup UCS lab
Hi Any one have experience of setting up UCS lab using UCSPE. Can I setup the UCS lab at home? Do I need other physical devices? Thank you
Hi Any one have experience of setting up UCS lab using UCSPE. Can I setup the UCS lab at home? Do I need other physical devices? Thank you
I'd like to be able to capture packets between two servers on the same VLAN/subnet within UCS. We are running Windows on VMWare on UCS. What are some suggestions for accomplishing this? On a Nexus switch the monitor command will let you capture traff...
Hello, I am trying to get some understanding here on VMQ connection policies on systems running ESXi. I cannot find much information on this to be honest and am growing more confused by it. Currently, we have VMQ set up as: - Number of VMQs: 16 - ...
UCS mgr 4.0.4aHX240C-M4SX Inoperable since the discovery ,it was working fine before the re-acknowledge, it's an hyperflex cluster rebuilt from scratch, other 2 servers are fine.Already tried to reset, recover, re-acknowledge, recommission but no suc...
Any suggestions what to check on cisco FI level to avoid c3 discards which we see in a few our Cisco UCS 6332 FI's ? 2 pairs runs without any errors and other 2 pairs reporting c3 via snmp. According storage team all configurations are identical on...
This may not be possible, but here's hoping. My VMware environment is 100% Cisco UCS B servers. I had an incident recently where our ESXi host servers became disconnected from our vCenter Server. Now per VMware support we need to shutdown the guest V...
Trying to setup LDAP login with username credentials, but only workswith admin account, these are newly installed, Cisco Systems Inc UCSC-C240-M5SX, tried several config options, but still does not work
Like the title says, I have two UCS C220 M4S servers and they only have a single PSU installed in each chassis. If I purchase a secondary identical PSU, do the firmware versions need to match? Or can I just hot-install them and call it a day?
say I have a C240 M5 server directly dual 10Gbps connected to a pair FI6200 (FI ports are configured as Server ports). There is also storage connected on FI via native FC. The FI is running as Ethernet end host and FC switch mode (local zoning is con...
I have several unlicensed UCS systems that I use in a lab environment for testing, writing documentation, etc. They of course generate "license-graceperiod-expired" F0676 and F0673 faults. Although it functions, it would be nice to not see them. Does...
cannot create virtual disks or RAID partition. Option 'Create virtual drive from unused physical disks' is grayed out.. Please refer attached screenshots
I am looking for more information on the sanitization process for the Nexus 3548 series (Part number: SG350X-48P-K9-NA) Based on the generic document called Statement of Policy - removal of data on Cisco and the 3548 general architecture.The costume...
Been meaning to ask this for ages as I can't find a reason online but this expires every year (or when the cluster name changes) I think we're all aware and there's a plethora of guides out there detailing how to regenerate it but what does it do?Whe...
Hello Why would a brand new UCS C220 with 4 x 1.8 TB (10K) HDD in RAID 10 give me only 50 MB/s write speeds on a lab system that is under no load at all (see ISE Alarm messages below)? I have installed ESXi 6.7u3 (using the vendor Cisco .iso) on ...
Hello, I am currently exploring Cisco IMC programming guide using REST API to automate the staging process and management of Cisco UCS-C rack mounted servers. I have looked up several common tasks as stated in the programming guide, however I could n...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-16-2024 02:26 AM | ||
04-04-2024 11:22 AM | ||
03-18-2024 06:52 AM | ||
02-27-2024 07:34 AM | ||
02-20-2024 12:52 PM |