Hello All,
I am a newbie to Cisoc UCS E-Series Server ( with ISR 4331 ). I was configuring the CIMC IP. Below is the config I did for CIMC Access using the E-Series Server's Internal NIC GE1 and routers UCSE 1/0/1 Interface.
Physicaly Connectivity I did is connected a Cable to Routers GE0 Inteafce with a PC where I assigned a same block IP ( 10.7.29.210 ). From PC I can Ping G00/0/0 but not the CIMC IP ( 10.7.29.202 ). Also from Router I can Ping G0/0/0 IP but not CIMC IP. I also added "sh ip interface brief" command output in case it helps.
Can you advise what could be the issue ?
==================================================
interface GigabitEthernet0/0/0
ip address 10.7.29.201 255.255.255.0
negotiation auto
interface ucse1/0/1
ip unnumbered GigabitEthernet0/0/0
no negotiation auto
switchport mode trunk
ucse subslot 1/0
imc access-port shared-lom console
imc ip address 10.7.29.202 255.255.255.0 default-gateway 10.7.29.201
ip route 10.7.29.202 255.255.255.255 ucse1/0/1
=============================================================
Command Output
Roter#sh ip interface brief
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 10.7.29.201 YES NVRAM up up
GigabitEthernet0/0/1 unassigned YES NVRAM administratively down down
GigabitEthernet0/0/2 unassigned YES NVRAM administratively down down
GigabitEthernet0/1/0 unassigned YES unset down down
GigabitEthernet0/1/1 unassigned YES unset down down
GigabitEthernet0/1/2 unassigned YES unset down down
GigabitEthernet0/1/3 unassigned YES unset down down
GigabitEthernet0/1/4 unassigned YES unset down down
GigabitEthernet0/1/5 unassigned YES unset down down
GigabitEthernet0/1/6 unassigned YES unset down down
GigabitEthernet0/1/7 unassigned YES unset down down
ucse1/0/0 unassigned YES NVRAM administratively down down
ucse1/0/1 10.7.29.201 YES unset up up
GigabitEthernet0 unassigned YES NVRAM administratively down down
Vlan1 unassigned YES NVRAM administratively down down
Router#ping 10.7.29.201
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.7.29.201, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
Router#ping 10.7.29.202
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.7.29.202, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
Router#
Router#show platform
Chassis type: ISR4331/K9
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
0 ISR4331/K9 ok 00:26:50
0/0 ISR4331-3x1GE ok 00:25:42
0/1 NIM-ES2-8 ok 00:25:42
1 ISR4331/K9 ok 00:26:50
1/0 UCS-E140S-M2/K9 ok 00:25:42
R0 ISR4331/K9 ok, active 00:26:50
F0 ISR4331/K9 ok, active 00:26:50
P0 PWR-4330-AC ok 00:26:27
P2 ACS-4330-FANASSY ok 00:26:27
