I was configuring the CIMC IP. Below is the config I did for CIMC Access , method using the E-Series Server's Internal NIC GE1 and routers UCSE 1/0/1 Interface.
Physical Connectivity I did is connected a Cable to Routers GE0 Interface with a PC where I assigned a same block IP ( 10.7.29.210 ). From PC ( 10.7.29.210 ).
I can Ping G00/0/0 but not the CIMC IP ( 10.7.29.202 ). Also from Router I can Ping G0/0/0 IP but not CIMC IP. I also added "sh ip interface brief" , “ sh platform” command output in case it helps. Can you advise what is wrong I am doing here ?
interface GigabitEthernet0/0/0 ip address 10.7.29.201 255.255.255.0 negotiation auto
interface ucse1/0/1 ip unnumbered GigabitEthernet0/0/0 no negotiation auto switchport mode trunk
Interface IP-Address OK? Method Status Protocol GigabitEthernet0/0/0 10.7.29.201 YES NVRAM up up GigabitEthernet0/0/1 unassigned YES NVRAM administratively down down GigabitEthernet0/0/2 unassigned YES NVRAM administratively down down GigabitEthernet0/1/0 unassigned YES unset down down GigabitEthernet0/1/1 unassigned YES unset down down GigabitEthernet0/1/2 unassigned YES unset down down GigabitEthernet0/1/3 unassigned YES unset down down GigabitEthernet0/1/4 unassigned YES unset down down GigabitEthernet0/1/5 unassigned YES unset down down GigabitEthernet0/1/6 unassigned YES unset down down GigabitEthernet0/1/7 unassigned YES unset down down ucse1/0/0 unassigned YES NVRAM administratively down down ucse1/0/1 10.7.29.201 YES unset up up GigabitEthernet0 unassigned YES NVRAM administratively down down Vlan1 unassigned YES NVRAM administratively down down
Router#ping 10.7.29.201 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.7.29.201, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
Router#ping 10.7.29.202 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.7.29.202, timeout is 2 seconds: ..... Success rate is 0 percent (0/5)
Also added the arp output from Router , where it shows CIMC IP arp is incomplete.
Router#sh ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 10.7.29.201 - 00aa.6ef6.2760 ARPA GigabitEthernet0/0/0 Internet 10.7.29.202 0 Incomplete ARPA Internet 10.7.29.210 0 a44c.c802.980d ARPA GigabitEthernet0/0/0
i have installed two numbers of cisco VIC 1385 card on UCS C240M5 server but in CIMC VIC adapter section only one card is listed. i have installed the cards in slot number 4 & 5. in VIC adapter section only slot 5 is showing. In PCI adapter i could se...
One of the great benefits of deploying Cisco's Container Platform on Cisco Hyperflex is the ability to get persistent storage for containers out of the box with minimal configuration. This works well for containers where you require the data to surv...
There has been a few announcements lately regarding Cisco's Container Platform (a.k.a: CCP) and they've all been good. Having integration with AWS allows CCP to deploy Kubernetes clusters on vSphere or EKS from the same control point. But anot...