About o.elmohri

o.elmohri · 04-12-2010

I'm configuring a point to multipoint which is the following:interface Tunnel1 ip address 10.0.0.2 255.255.255.0 no ip redirects ip mtu 1440 ip hold-time eigrp 90 120 ip nhrp authentication <key> ip nhrp map multicast <public ip> ip nhrp network-id 1...

o.elmohri · 02-21-2010

Hi,I have to choose the 3750 or the 4506 catalysts in the following situation:I have 12 switchs of access layer with 10/100 Ethernet ports.6 duplicated fibers arriving to the core layer.PoE is supported but no IPT for the moment.About 300 users.What ...

o.elmohri · 02-14-2010

Hi everyone,I need to limit the number of packets per second on a well known port. Is that possible using ASA 5505 without IPS? and How?Regards,Omar

o.elmohri · 01-05-2010

Hi guys,I'm using a Cat 4507R-E with a sup engine IV which was at first purchased with a Cat 4506 and I'm using it in the new chasis, while loading I got the problem that there is an unknown backplane. So i dowloaded a new IOS and I got the same prob...

o.elmohri · 10-19-2009

Hi,Please can some helps me using LMS to find to whith switch port number a computer is connected when I have only its IP address?I'm using tracking but it's not working and every thing else is well done.Regards,Omar

o.elmohri · 05-02-2010

Hi,I finaly did the sniffing on the spoke side.But, all pings from that router can monitor a reply. And not the one through 10.0.0.1 (the hub tunnel side) unless the public IP of the hub can show a reply.Any idea??

o.elmohri · 04-21-2010

Hi,Here is the placement of the sniffer:HUB LAN |-------------| NHRP SERVER ROUTER |---------------| Switch w/SPAN and sniffer |------------------| INTERNET ROUTER |------------(INTERNET)------->>I run a continue ping to 10.0.0.3 from the NHRP server...

o.elmohri · 04-20-2010

I did a sniffing on the HUB. But the only packets that I got to the 10.0.0.3 were the NHRP and the EIGRP and not the ping unless I was running a ping on the router!!

o.elmohri · 04-20-2010

Hi Federico,Here is the debug:HUB#*Apr 20 09:03:39.433: IP: s=10.0.0.1 (local), d=10.0.0.3 (Tunnel1), len 60, sending, proto=88ping 10.0.0.3Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.0.0.3, timeout is 2 seconds:*Apr 20 09:03:4...

o.elmohri · 04-18-2010

Hi Federico,There is another point that, may be it's affecting the tunnel.As right now, in the Hub. There is another router which is connected to the one where is the DMVPN. In other words, the is the ISP router connected to a leased line which is us...

Member Since	‎09-10-2007 07:25 AM
Date Last Visited	‎08-18-2017 03:54 AM
Posts	32

User Statistics

User Activity

NHRP encapsulation error

Cat 3750 vs Cat 4500

ASA 5505 packets limit

Catalyst 4500 IOS loading problem

IP@ to port number with LMS

Re: NHRP encapsulation error

Re: NHRP encapsulation error

Re: NHRP encapsulation error

Re: NHRP encapsulation error

Re: NHRP encapsulation error