Cisco Community
English
Register
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Tony Huynh
‎02-25-2021
Enthusiast
Technical Marketing Engineer with responsibilities for Product Marketing for Unified Communications express solutions in the enterprise branch. Expertise: CME CUE SRST UC500
Recent Badges
Awards
Recent Badges
See all
100 Helpful Vote
1 Accepted Solution
5 Accepted Solution
30 Helpful Vote
10 Helpful Vote
1 Helpful Vote
50 Replies
20 Replies
10 Replies
5 Replies
Stats
Member since ‎10-22-2005
260
Posts
32
Helpful
9
Solutions

Re: Router 2811 and Cisco ip softphone

Created by in IP Telephony and Phones
01-24-2007
01-24-2007
Hi,CIPC support with CME was stared with CME 4.0, so you should be fine. Here is a config guide.http...

Re: CCME DID configuration

Created by in IP Telephony and Phones
01-24-2007
01-24-2007
You config looks fine for the most part. Try changing the following.dial-peer voice 1 pots incoming ...

Re: CME in Mexico

Created by in IP Telephony and Phones
01-22-2007
01-22-2007
Hi,Spanish localization is supported as of CME 4.0.http://www.cisco.com/cgi-bin/tablebuild.pl/CME-Lo...

Re: CME - IOS versions

Created by in IP Telephony and Phones
01-21-2007
01-21-2007
Hi, If you don't need features provided by CME 4.0(2) or 4.0(3), then I would suggest using the late...

Re: CME fax question

Created by in IP Telephony and Phones
01-21-2007
01-21-2007
What type of gateway is this? H323 should work for fax on a CME.

Re: CallManager Express music-on-hold

Created by in IP Telephony and Phones
01-21-2007
01-21-2007
Command is "multicast moh" underneath ephone-dn.http://www.cisco.com/en/US/products/sw/voicesw/ps462...

Re: CallManager Express music-on-hold

Created by in IP Telephony and Phones
01-20-2007
01-20-2007
Hi,Keep in mind that in older versions of CME, for calls between IP phones on same CME, only tone-on...

Re: ccme: max # of conference

Created by in IP Telephony and Phones
01-20-2007
01-20-2007
Hi,If you upgrade to CME 4.1 (12.4(11)XJ - BU special for early adopters), you can have up to 8 part...

Re: Call problem with CCME 4.0

Created by in IP Telephony and Phones
01-19-2007
01-19-2007
Please verify that you are using the correct phoneload for CME 4.0. If the incorrect phone load is u...

Re: 2811 router cannot detect vic-4fxs/did

Created by in IP Telephony and Phones
01-19-2007
01-19-2007
Have you checked the following?http://www.ciscotaccc.com/kaidara-advisor/voice/showcase?case=K578154...

Re: TAPI in CME

Created by in IP Telephony and Phones
01-19-2007
01-19-2007
Not sure if you have heard yet, Cisco is coming out with a product, Unified CallConnector, which wil...

Re: TAPI in CME

Created by in IP Telephony and Phones
01-19-2007
01-19-2007
On your CME, perform "show ephone tapi" and see what the other device is. The output should give you...

Re: Incoming Caller ID issue on CME

Created by in IP Telephony and Phones
01-19-2007
01-19-2007
To find out if line is providing caller-id, enable the following debug and make an inbound call.debu...

Re: Incoming Caller ID issue on CME

Created by in IP Telephony and Phones
01-18-2007
01-18-2007
First, did you perform "shut/no shut" after you added the "caller-id enable" command? If you didn't,...

Re: IP Phone Clock not sync with CME router

Created by in IP Telephony and Phones
01-18-2007
01-18-2007
Can you perform the following?telephony-servicecreate cnf-filesAnd then reset the phones. Let me kno...
Public Statistics
Date Registered ‎10-22-2005 01:25 PM
Date Last Visited ‎02-25-2021 11:08 PM
Total Messages Posted 260
Total Helpful Votes Received 32
Helpful Votes From