About hustler0002

hustler0002 · 08-23-2011

Hi,I have a pinging problem. I have this cfg.Webservice PC --> 6506 switch ---> cisco1 3750 --> cisco2 3750 ---> PC1here the cfgs for each device and I removed some of the extra stuff.Cfg on cisco 6506 Sup720Router#sho runBuilding configuration...Cu...

hustler0002 · 02-23-2011

Hi,This is a wierd problem that I can't seem to find the answer for online. I just put together a 6506-e and now I'm trying to configure it like our current 6509. I tried to create a vlan on the switch and wanted to add it to the FWSM. I followed ...

hustler0002 · 02-15-2011

I have one 6506 switch and one 6509 switch. I need to upgrade them to the same firmware/software. Below are the sho modules for each switch:6506Router#sho moduleMod Ports Card Type Model Se...

hustler0002 · 01-21-2011

Hi,I currently have this in our Sup720:boot system flash bootflash:s72033-jk9o3sv-mz.122-17a.SX3.binboot bootldr sup-bootflash:s72033-psv-mz.122-17a.SX1.binI downloaded s72033-mp001-pz.122-33.SXH5I read the documentation on Upgrading Software Images ...

hustler0002 · 12-23-2010

Hi,We need to upgrade our fwsm to a more current version, is there any problems I should be aware of in upgrading from our updated version? Our IT guy left so I'm left to try keep our firewall up to date. Our sup720 is running ver. 12.2(14r)s9. I ...

hustler0002 · 08-23-2011

Sorry about that. I usually double check my ip addresses because they're important. All subnet are 192.10.10.xxx, 10.17.18.xxx, 192.4.3.xxx and 10.94.8.xxx.Oh and on the 3550 switch I removed the ip route 10.17.18.103 255.255.255.255 192.4.3.2 beca...

hustler0002 · 08-23-2011

our FWSM has a default ip route already to some other network. It's hard to figure out exactly what's going on when you don't have the configuration of the other Cisco2 3750 switch. if you look below I hooked up a 3550 cisco switch to emulate the C...

hustler0002 · 08-23-2011

The Webserver PC in 10.94.8.72 which is nat'd to 192.4.3.198. The PC1 ip address is 10.17.18.103 but I ASSUME it is some how routed to 192.4.3.1. I had set up my own test lab right now and I hooked up a Cisco 3550 where I configured the port.vlan 11...

hustler0002 · 02-24-2011

Thanks Jennifer that's exacly what I needed. We still have an older version 6509 FWSM and it still uses the old nameif format. I didn't know there was a new way of doing it. Thanks again.

hustler0002 · 02-23-2011

Thanks for the reply and help.I'll read it and try to upgrade the switch.

Member Since	‎07-19-2010 08:05 AM
Date Last Visited	‎08-18-2017 03:56 AM
Posts	30

User Statistics

User Activity

Can't ping from 6506 to 3750 to another 3750

FWSM 6500 nameif configuration problem

Same configuration upgrade for a 6506 and a 6509

6509 with Sup 720 configuration upgrade

upgrading fwsm 6509 from 1.1(3) to 4.x

Re: Can't ping from 6506 to 3750 to another 3750

Re: Can't ping from 6506 to 3750 to another 3750

Re: Can't ping from 6506 to 3750 to another 3750

Re: FWSM 6500 nameif configuration problem

Re: Same configuration upgrade for a 6506 and a 6509