I dont get the option of selecting any phone loads.  Its empty. I did format the flash and then reloded the UC520-8.0.0 zip  file and it tells me that "There are no phone loads file in the software pack you provided". ... View more

Like you said I did the upgrade again.  This time the I get an error message " Please make sure that there is no FTP/TFTP server running on your PC" this happens at the point of CME Files upload in progress,please wait....(37). Is there any other way to upgrade this? ... View more

I did an upgrade to 8.0.0 and it errored out few times and I gave up.  It gives TFTP errors etc.  Is there any other way to upgrade the IOS other than CCA? ... View more

Here it is #dir Directory of flash:/     1  -rw-         660  Jan 25 2010 10:14:44 -05:00  vlan.dat     2  -rw-    37988016  Jan 25 2010 10:16:48 -05:00  uc500-advipservicesk9-mz.150-1.XA     3  drw-           0  Jan 25 2010 10:17:20 -05:00  phones    99  -rw-     2843434  Jan 25 2010 14:25:10 -05:00  TEAMLOGIC_FW_08.wav 128184320 bytes total (180224 bytes free) ... View more

Syslog logging: enabled (0 messages dropped, 0 messages rate-limited,                 0 flushes, 0 overruns, xml disabled, filtering disabled) No Active Message Discriminator. No Inactive Message Discriminator.     Console logging: level debugging, 556 messages logged, xml disabled,                      filtering disabled     Monitor logging: level debugging, 32 messages logged, xml disabled,                      filtering disabled         Logging to: vty68(31)     Buffer logging:  disabled, xml disabled,                      filtering disabled     Logging Exception size (4096 bytes)     Count and timestamp logging messages: disabled     Persistent logging: disabled No active filter modules. ESM: 0 messages dropped     Trap logging: level informational, 548 message lines logged ... View more

000829: Nov  9 17:51:39.640: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1/0, changed state to down UC520# 000830: Nov  9 17:51:40.644: %LINK-3-UPDOWN: Interface FastEthernet0/1/0, changed state to down UC520# 000831: Nov  9 17:51:50.032: %LINK-3-UPDOWN: Interface FastEthernet0/1/0, changed state to up 000832: Nov  9 17:51:51.032: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1/0, changed state to up I also dont see the Phone loads in CCA.  I copied the phone loads again using CCA and still have the same issue. ... View more

Steve, Still not registering. Jibu ... View more

Hello Steve,   Thanks for the prompt reply.   I am working on a UC520 and in the process of the upgrade it became unresponsive.  I had to restart the upgrade and then got the UC 500 working but however the phones are not registering.  The phones I have are 7970, 7940,7941 & 7931.  I used CCA 2.1.1 to do the upgrade and dont see any phone loads on it. I even tried using the phone loads upgrade but it tells me that the phone loads are alredy there.   I think we need to recreate the CFN files.  I am attaching the sh run and show telephoney service.   Let me know if this helps.   Regards,   Jibu ... View more

running config ... View more

I did that too and did a reload.  I am attaching a text file What is the "WDC is not configured" message ? ... View more

That helped with the boot, however there is no IP address to access the device. ... View more

I used another flash from a working UC500 and still cannot get it to reload.  When I use the new CF and did a copy flash:UC520w-8u04fxo-k9-factory.cfg start and reloaded the box it still does not allow me to access the UC500 from CCA.  There is a message "WDC is not configured" and prompts me with a question "would you like to enter the initial configuration dialog?[yes/no] Installed image archive? "  not sure what to do. ... View more

Marcos & Steve, I am going to try Marcos's suggestion.  Meanwhile a little background.  This was a UC500 lying around and has not been used for some time.  I powered it up to check the UC500 and could not access it using CCA as DHCP was not working.  Finally Hyperterminal worked and I could see the boots.  I also see a "WDC failure"  something like that and it brings me to the config menu.  Not sure how to proceed after that.  All the Ethernet ports also stop working.  I tried to copy the default config to start and that did not help.  When I do a show run I just see few lines of the config loaded.  Seems like there is a corruption and I may need to reload the config. I will set the VLAN and update you. Regards, Jibu Mathews ... View more