Cisco Community
English
Register
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Andreas Schneider
‎12-15-2020
Beginner
Recent Badges
Awards
Recent Badges
See all
10 Helpful Vote
50 Replies
1 Helpful Vote
1 Accepted Solution
20 Replies
10 Replies
5 Replies
Stats
Member since ‎03-15-2011
71
Posts
10
Helpful
1
Solution

Re: 4500X change vss domain

Created by in Switching
12-14-2020
12-14-2020
Hi,the procedure:switch#switch virtual domain 2 Domain ID 2 config will take effect only after the e...

Re: 4500X change vss domain

Created by in Switching
12-14-2020
12-14-2020
Thank you for the document!I'll give option 1 a try (which is the same I wrote earlier ) Kind regard...

Re: 4500X change vss domain

Created by in Switching
12-14-2020
12-14-2020
Hello BB,yes a unique ID will be the best, but till now it was not planned to connect both systems w...

4500X change vss domain

Created by in Switching
12-14-2020
12-14-2020
Hello,is it possible to change the "switch virtual domain" after the VSS is already build?I have two...

Re: MAC address learning while port-security is on

Created by in Network Management
10-15-2020
10-15-2020
Hi,depending on the switch model, you can implement a mac access-list. It's like an IP access-list b...

Re: Catalyst 3560-CX Power Device detected : Cisco PD issue

Created by in Network Management
10-15-2020
10-15-2020
Hello Robert,I have about 20 of 3560CX-12PD-S, also running 15.2(7)E1 and never saw this. May be a "...

Re: EEM no (TCL)bytecode support anymore since 15.2.(7)E2 ?

Created by in Network Management
10-15-2020
10-15-2020
Hi Jonathan,is there any chance that this will be supported again in the future? Kind regards,Andrea...

EEM no (TCL)bytecode support anymore since 15.2.(7)E2 ?

Created by in Network Management
07-29-2020
07-29-2020
Hello,I recently upgraded from 15.2(7)E1 to 15.2(7)E2. After the reload all my EEM policies were no ...

Re: DHCP relay issue on Nexus 3k when used with vrf

Created by in Switching
03-26-2020
03-26-2020
Hi Cristian,thank you very much for the excellent explanation! I think you're right. I bet the print...

Re: DHCP relay issue on Nexus 3k when used with vrf

Created by in Switching
03-26-2020
03-26-2020
Hi,I was not able to reset the printer to factory-defaults, got an access denied...But I was able to...

Re: DHCP relay issue on Nexus 3k when used with vrf

Created by in Switching
03-25-2020
03-25-2020
Hi,sorry, I've forgotten some. I testet with a Canon and a Lexmark Printer. Both behave same. The pr...

Re: DHCP relay issue on Nexus 3k when used with vrf

Created by in Switching
03-25-2020
03-25-2020
Hi,I can not post the full packet capture in raw, for some privacy restrictions. But I exported some...

Re: DHCP relay issue on Nexus 3k when used with vrf

Created by in Switching
03-24-2020
03-24-2020
Hi,I was able to do a packet capture on the remote site. I used a monitor session on the 2960-X.So, ...

Re: DHCP relay issue on Nexus 3k when used with vrf

Created by in Switching
03-24-2020
03-24-2020
Hi,yes, one Nexus has the ".2", the other has the ".3" and the hsrp address is the ".1". I think the...

Re: DHCP relay issue on Nexus 3k when used with vrf

Created by in Switching
03-23-2020
03-23-2020
Hi,the debug is from the Nexus. There is no debug from the 2960-X, it's just L2. All the dhcp relay ...
Public Statistics
Date Registered ‎03-15-2011 06:12 AM
Date Last Visited ‎12-15-2020 01:28 AM
Total Messages Posted 71
Total Helpful Votes Received 10
Helpful Votes Given To
See all >
Helpful Votes From
See all >