About CompCJtoo

CompCJtoo · 07-15-2020

Hello. Currently on an entire LAN VLAN1 is the only vlan configured among SG300's in a hub and spoke topology. I'm trying to setup a trunk between a 3560 switch to the "hub" SG300 to pass data over vlan 1. I've tried the below SG300:int gi14switch...

CompCJtoo · 09-24-2019

Hi all. I have two ISR4321 routers connected and have end to end communication at least from the L3 interfaces of each router (RTR1 and RTR2) to any device on the rest of the network. Granted I've only tested with icmp. Nonetheless, broadcast does...

CompCJtoo · 09-20-2019

Hi all. For a couple of years I've had two Cisco 1941 routers running IOS and BVI interfaces to support some end user devices. I have two Cisco ISR4321 running IOS-XE which from what I've read you must do BDI interfaces. I attached a diagram and appl...

CompCJtoo · 01-24-2019

Hi All. Is it possible to configure individual APs that are joined to a controller for settings such as login banner, username/password, syslog, ssh, ntp, and snmp? Or do the APs essentially take on the configuration of the controller once they joi...

CompCJtoo · 01-17-2019

Hello All. I'm trying to see what the logging buffer size is for a WLC running code 8.3.140. In the GUI it shows the syslog level is: Informational and the Buffered Log Level is: Notifications. If I use the command show logging, it shows me the fo...

CompCJtoo · 07-17-2020

BB, Hello. I tried the changes and still no luck. The spanning-tree states remained the same. I'm not at all familiar with Cisco's small business switches, but here are a few more things I noticed while trying different configs. 1. On the 3560 I crea...

CompCJtoo · 07-16-2020

BB,Hello. I tried the switchport mode trunk on the SG300 and still no joy. I attached the relevant config of the 3560 and SG300. There's also some spanning-tree output in there. I noticed despite VLAN 1 being Up/Up on the 3560, the 3560 sees itse...

CompCJtoo · 07-15-2020

BB,Hello. When I go to int gi14 there isn't any command option available to set the encapsulation. I just get:accesscustomerdefault-vlanforbiddengeneralmodeprivate-vlanprotected-porttrunk If I go further with either trunk or mode, there still isn't...

CompCJtoo · 09-26-2019

I created this post because I had ran into an issue based on one project that I initially posted about. Below is the other post which has the solution. https://community.cisco.com/t5/routing/ios-xe-bridge-domain-and-broadcasts/m-p/3929817#M322220

CompCJtoo · 09-26-2019

I figured out how to get the ISRs with IOS-XE working using BDI instead of BVI. Aside from the config, on RTR2-4321 I had to connect Gi0/1/0 of the switch module to the built-in Gi0/0/0 for the end user device to be able to access LAN resources a...

Member Since	‎05-01-2014 09:16 AM
Date Last Visited	‎09-23-2022 01:20 PM
Posts	35

User Statistics

User Activity

Trunk 3560 to SG300 with Only VLAN1 Used

IOS-XE bridge-domain and broadcasts

Replacing BVI Int Cisco 1941 (IOS) with BDI Int Cisco ISR4321 (IOS-XE)

Access Point Configuration

WLC Logging Buffer Size

Re: Trunk 3560 to SG300 with Only VLAN1 Used

Re: Trunk 3560 to SG300 with Only VLAN1 Used

Re: Trunk 3560 to SG300 with Only VLAN1 Used

Re: IOS-XE bridge-domain and broadcasts

Re: Replacing BVI Int Cisco 1941 (IOS) with BDI Int Cisco ISR4321 (IOS-XE)