The password for: ********************************************** rommon 3 > priv Password: rommon 4 > priv Password: rommon 5 > cookie cookie: 01 01 00 04 27 fe 00 ea 3e 00 00 ff 01 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 6f e6 00 00 00 00 ff ff ff 50 04 49 11 ec 03 ff ff ff ff ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 rommon 6 > ************************************************* Should be: 67ed. I can give directions on how to figure it out obviously, but I can try and help you guys get your routers up and going. I will look for an 837 to see if I can find the correct cookie values. ... View more

Please post your new cookie value and I will try to figure out the new password. Thanks Anthony ... View more

You have to use the priv command in ROMMON to get to where you can enter the cookie output. rommon 14 > priv Password: You now have access to the full set of monitor commands. Warning: some commands will allow you to destroy your configuration and/or system images and could render the machine unbootable. rommon 15 > Since the cookie is set to all zero's the password should be 0000. HTH Anthony ... View more

Look on the flash (dir flash:) and see if there is a crashinfo file. If there is, use the "more flash:filename" command where filename is to be replaced with the crashinfo name. Send it to me at answanso@cisco.com and I will take a look at it. ... View more

Better send a show version as well so I can see what version of IOS you are on too =) Anthony ... View more

The bug is currently in (J)unked state because of this reasoning. I would argue this isnt correct behavior. Can you send me your whole config, I will try it in the lab. If I can reproduce it I will open the defect back up. In the mean time, if you can move the management to vlan to 1 and see if it resolves the issue, that would be helpful too for opening the defect as well. Please send the config to answanso@cisco.com. Thanks Anthony ... View more

Per CSCsc92347, this can happen if Vlan1 (the management vlan) is not configured as such. Meaning has an IP address assigned to it. Can we please see a configuration from one of these switches? ... View more

First of all those networks are the same, so its not really different networks. 192.168. 1.00000000 255.255.255.11111100 192.168. 1.00000001 <- First host .1 192.168. 1.00000010 <- Last host .2 192.168. 1.00000011 <- Broadcast .3 With Routing Protocols such as EIGRP and OSPF you are enabling the interface to participate in the routing protocol and not "advertising" a network per say. Don't get me wrong, you are advertising routes, I just think you are looking at this wrong. The network command enables an interface to participate. If you have: 192.168.1.5/30-rtr1-192.168.1.1/30--192.168.1.2/30-rtr2 Under rtr1 you would have something like this: router eigrp 10 no auto network 192.168.1.1 0.0.0.0 network 192.168.1.5 0.0.0.0 Under rtr2 you would have something like this: router eigrp 10 no auto network 192.168.1.2 0.0.0.0 This configuration basically says the interfaces with .1, .2, and .5 participate in eigrp. The result will be rtr2 will have an eigrp learned route for .4/30 and a directly connected for .0/30. rtr1 will have two directly connected routes for .0/30 and .4/30. So to answer your questions eigrp must be enabled on any interface you want to participate in eigrp. HTH Anthony ... View more

I don't think this is possible without clearing the config or deleting the vlan.dat. The state that you are talking about is the intial config where vtp has no-domain, and is in a plug and play mode where it would accept the first domain and configuration it receives on one of its interfaces. To my knowledge this is only going to happen with wri erase and a delete vlan.dat. Because we need a valid vtp domain name to create vlans, with such a feature we may also run into an issue where the vlans created under that domain need to be removed as well when the domain is nulled. Basically the same effect as deleting the vlan.dat. Regardless, there was a defect enhancement for a similar command on catos, but it was ultimately closed. HTH Anthony ... View more

The only way to truely tell the cause of the reload is to look at the crash context and the stack at the time of the crash, decode them to see if the error is indeed software or hardware in nature. Since non of this is available to us yet, it is impossible to say whether a software upgrade will resolve this issue. The link above is useful, but it will not lead you to the corrective course of action, it simply states to open a tac case. Thanks Anthony ... View more

Hi Jason, The most important part of the crashinfo was truncated from that file. Could you please unicast the full "show stacks" to me @ answanso@cisco.com. Thanks Anthony ... View more

Can I see the output of the "show stacks" and I will take a look at the crash. Thanks Anthony ... View more

Do you have any monitor sessions that are the destination to any gig2/x interfaces? Can I see the output from a "show run"? This can happen if you have a large span session overwelm a portasic that controls multiple ports. Anthony ... View more