Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About NicP270591
Stats
Member since
12-15-2010
129
Posts
14
Helpful
1
Solution
Created by
NicP270591
in IP Telephony and Phones
in IP Telephony and Phones
10-19-2013
08:16 PM
10-19-2013
08:16 PM
Hi Andrew, Config as follows: dial-peer voice 1007 voip corlist outgoing callMobile description IP Mobile Calls translation-profile outgoing 1 preference 1 destination-pattern 004........ session protocol sipv2 session target sip-server voice-class codec 1 dtmf-relay rtp-nte no vad ! dial-peer voice 2017 pots corlist outgoing callMobile description POTS IP Mobile Calls BKCLID preference 2 destination-pattern 004........ port 0/0/0 forward-digits 14 prefix 1831 no register e164 ! sip-ua credentials username USERNAME password 7 PASSWORD realm REALM authentication username USERNAME password 7 PASSWORD realm REALM no remote-party-id retry invite 2 timers trying 150 registrar dns:sipprovider.net expires 3600 sip-server dns:sipprovider.net ! I attempted debug as requested, nothing showed up in my telnet session during a call attempt. Odd. Nic.
... View more
Created by
NicP270591
in IP Telephony and Phones
in IP Telephony and Phones
10-17-2013
10:30 PM
10-17-2013
10:30 PM
Hi guys, I have a CME router with both SIP dial peers (preference 1) and FXO PSTN dial-peers for failover (preference 2). When SIP is unreachable, you go to dial a call, it hangs on "Ring out" for a minute or so and then returns busy tone/unknown number error. There is no failover to the preference 2 dial peer on the FXO port (same pattern just preference 2 and mapped to a port rather than SIP). 1. Why is there not failover? 2. Can I reduce the hunt time to a few seconds before it cancels SIP and switches to the PSTN peer? 3. Does this even work by default on CME, or will I need SRST on the router? Nic.
... View more
Labels:
Created by
NicP270591
in IP Telephony and Phones
in IP Telephony and Phones
09-20-2013
05:35 PM
09-20-2013
05:35 PM
Hi Haitham, I understand that is the default procedure for adding backgrounds, however as mentioned my 7975 deployment is setup as I have shown above, with the images in the desktops folder, and it works perfectly. I have aliased for both locating the file, and the fact that each List.xml has a different file name dependant on the phone, so multiple phones can have XML lists on the router without a name confusion. It is my understanding the alias command should prevent any issue as to not being able to locate the file. If it works for our 7975's on this router why wouldn't it work for the 7961's? Nic.
... View more
Created by
NicP270591
in IP Telephony and Phones
in IP Telephony and Phones
09-20-2013
03:17 PM
09-20-2013
03:17 PM
I am having an odd issue with CME background image. I have created the correct directories, XML file, sized thumbnail and full size. When you go to images menu on the 7961, the thumbnail is there to "select" but is blank, you can't see the image on the thumbnail, just a blank square box. When you click to select, the error message "File not found" is displayed and it obviously can't be selected. I have the exact same configuration working on 7975 phones - I merely changed images and file names for the 7961. Config is as follows: Directory of flash:/ 1 drw- 0 Apr 1 2012 16:29:14 +10:00 GUI 55 drw- 0 Apr 1 2012 15:23:54 +10:00 ATA 58 drw- 0 Apr 6 2012 12:10:08 +10:00 Rings 74 drw- 0 May 26 2012 22:42:30 +10:00 Desktops Directory of flash:/Desktops/ 75 drw- 0 Sep 27 2012 00:50:00 +10:00 320x216x16 79 drw- 0 Sep 27 2012 00:50:18 +10:00 320x196x4 86 -rw- 23167 Sep 27 2012 01:36:06 +10:00 OP-Color-7975.png 88 -rw- 4027 Sep 27 2012 01:38:02 +10:00 TN-OP-Color.png 89 -rw- 20983 Sep 27 2012 01:38:34 +10:00 OP-BW.png 90 -rw- 3541 Sep 27 2012 01:39:00 +10:00 TN-OP-BW.png Directory of flash:/Desktops/320x196x4/ 193 -rw- 132 Sep 21 2013 07:47:44 +10:00 7961-List.xml 7961-List.xml <CiscoIPPhoneImageList> <ImageItem Image=" TFTP:/Desktops/TN-OP-BW.png " URL=" TFTP:/Desktops/OP-BW.png "/> </CiscoIPPhoneImageList> TFTP Bindings tftp-server flash:/ Desktops/TN-OP-BW.png alias Desktops/TN-OP-BW.png tftp-server flash:/ Desktops/OP-BW.png alias Desktops/OP-BW.png tftp-server flash:/ Desktops/320x196x4/ 7961-List.xml alias Desktops/320x196x4/List.xml ____________________ Suggestions? Nic.
... View more
Labels:
Created by
NicP270591
in IP Telephony and Phones
in IP Telephony and Phones
08-20-2013
12:56 AM
08-20-2013
12:56 AM
Update - I have now decided to try and "select all" and go through to the end of the initialization. On the final page, even after everything has ticked, it says its going to import 0 users, create 0 mailboxes, etc, if I continue. However as mentioned my initial page does bring up all my extensions, they are just not selectable. Ideas?
... View more
Created by
NicP270591
in IP Telephony and Phones
in IP Telephony and Phones
08-19-2013
11:46 PM
08-19-2013
11:46 PM
Ken, You will need to create a dummy ephone and ephone-dn for the config, as you are effectively turning the port into an IP phone, it will need to have an "IP Phone" assosciated with it. ephone-dn 21 number 1000 description STCAPP dial ephone 10 device-security-mode-none mac-address XX.XX.XX.XX type anl button 1:21 note to find your analog mac address you can do a "sh stcapp device summary" on the router, which will bring up all ports configured with STCAPP and their mac address. HTH, Nic.
... View more
Created by
NicP270591
in IP Telephony and Phones
in IP Telephony and Phones
08-19-2013
07:52 AM
08-19-2013
07:52 AM
Hi Ken, Your best bet is probably to wait till after business hours as standard before altering config. Have a copy saved so if anything goes wrong you have a "restore to default" backup you can redeploy in a few minutes if needed. It has been a while since I have done a config on STCAPP, but from memory it should overlay right ontop of the current config, maybe with a shut/no-shut command if necessary on the port. It basically just changes the port directly from analog to IP capable. Nic.
... View more
Created by
NicP270591
in IP Telephony and Phones
in IP Telephony and Phones
08-19-2013
07:21 AM
08-19-2013
07:21 AM
I thought this had solved the issue, but it seems to have not. I converted to IE7 and enabled TLS 1.0, still the same issue.
... View more
Created by
NicP270591
in IP Telephony and Phones
in IP Telephony and Phones
08-19-2013
06:38 AM
08-19-2013
06:38 AM
Logged into CUE and am using initial setup wizard for the first time. Login fine, enter CME login details fine, when it comes to the screen to import individual extensions from CME, all the checkboxes and dropboxes beside the individual extensions are greyed out - EXCEPT the top row to "select all" - meaning I would have no option but to select all extensions, give all a mailbox, allow all administrative privledges etc. Everything has loaded and discovered fine, it's just telling me "all or nothing" in the initial stages of the wizard. Anyone seen this behaviour before?
... View more
Labels:
08-13-2013
10:41 PM
Hi, Further to what Leo has said: What model of the 7925G are you using specifically? eg. CP-7925G-A-K9, CP-7925G-W-K9, CP-7925G-E-K9 etc What country is the phone being deployed into? if it is a W model, the AP will need world mode configured on the Dot11Radio interface to register with the network. conf t int Dot11Radio1 world-mode dot11d country XX (both, indoor, outdoor) end. It sounds like an identical issue I dealt with last week, and this solved the issue. Also check obviously the phone has the correct SSID (case sensitive) and password, as well as security mode. HTH, Nic.
... View more
Created by
NicP270591
in IP Telephony and Phones
in IP Telephony and Phones
08-13-2013
10:31 PM
08-13-2013
10:31 PM
Ken, It sounds like you need to implement either a parallel hunt group or a shared line/overlay dn on each IP Phone. FXS ports will not natively work with hunt groups, you will need to convert it to be able to act like an IP endpoint using SCCP. This is done by configuring a feature called STCAPP. Info can be found at the below link: https://supportforums.cisco.com/docs/DOC-9443 HTH, Nic.
... View more
Created by
NicP270591
in Other Wireless - Mobility Subjects
in Other Wireless - Mobility Subjects
08-09-2013
01:26 AM
08-09-2013
01:26 AM
Rasika, Correct, configuring PIM fixed the issue. The calls are a little scratchy but I think this is just due to the router at this current point in time. Thank you very much! Nic.
... View more
Created by
NicP270591
in Other Wireless - Mobility Subjects
in Other Wireless - Mobility Subjects
08-09-2013
12:26 AM
08-09-2013
12:26 AM
Hi Rasika, PIM has not been configured on this router, as it was not required in the previous config - Would it be beneficiary in this instance, and if so, what is the simplest way to configure it? I just checked the new config notes, it includes a Transcoding profile config on the router. I have known MOH issues in the past to be related to transcoding problems - does it sound like a possible cause? Should I try disabling the transcoder profile on the router and seeing if there is success after? The basic configuration wanted is as follows: inbound/outbound calls via SIP Trunks with DID. Outbound calls are linked to a codec preference list, consisting of G711u followed by G729. The SIP Provider only supports these 2 codecs - would a transcode profile even be required in this case? Nic.
... View more
Created by
NicP270591
in Other Wireless - Mobility Subjects
in Other Wireless - Mobility Subjects
08-07-2013
09:27 PM
08-07-2013
09:27 PM
No problem, will try over there. Thank you for your assistance!
... View more
Created by
NicP270591
in IP Telephony and Phones
10-22-2013
10-22-2013
I shut down my 1007 for testing and the call failed. But normally it
works fine. Very strange, I wil...
Created by
NicP270591
in IP Telephony and Phones
10-19-2013
10-19-2013
Hi Andrew,Config as follows:dial-peer voice 1007 voip corlist outgoing
callMobile description IP Mob...
Created by
NicP270591
in IP Telephony and Phones
10-17-2013
10-17-2013
Hi guys,I have a CME router with both SIP dial peers (preference 1) and
FXO PSTN dial-peers for fail...
09-20-2013
Hi Haitham,I understand that is the default procedure for adding
backgrounds, however as mentioned m...
09-20-2013
I am having an odd issue with CME background image. I have created the
correct directories, XML file...
Created by
NicP270591
in IP Telephony and Phones
08-20-2013
08-20-2013
Update - I have now decided to try and "select all" and go through to
the end of the initialization....
Created by
NicP270591
in IP Telephony and Phones
08-19-2013
08-19-2013
Ken,You will need to create a dummy ephone and ephone-dn for the config,
as you are effectively turn...
Created by
NicP270591
in IP Telephony and Phones
08-19-2013
08-19-2013
Hi Ken,Your best bet is probably to wait till after business hours as
standard before altering confi...
Created by
NicP270591
in IP Telephony and Phones
08-19-2013
08-19-2013
I thought this had solved the issue, but it seems to have not. I
converted to IE7 and enabled TLS 1....
Created by
NicP270591
in IP Telephony and Phones
08-19-2013
08-19-2013
Logged into CUE and am using initial setup wizard for the first time.
Login fine, enter CME login de...
08-13-2013
Hi,Further to what Leo has said:What model of the 7925G are you using
specifically? eg. CP-7925G-A-K...
Created by
NicP270591
in IP Telephony and Phones
08-13-2013
08-13-2013
Ken,It sounds like you need to implement either a parallel hunt group or
a shared line/overlay dn on...
08-09-2013
Rasika,Correct, configuring PIM fixed the issue. The calls are a little
scratchy but I think this is...
Public Statistics
| Date Registered | 12-15-2010 08:20 AM |
| Date Last Visited | 10-04-2019 03:08 PM |
| Total Messages Posted | 129 |
| Total Helpful Votes Received | 14 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 3 | |
| 7 | |
| 4 |
.jpg "VIP Collaborator"){kind=icon}
