Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About alanc3141592654
Stats
Member since
09-20-2007
84
Posts
4
Helpful
0
Solutions
Certifications
Created by
alanc3141592654
in Application Networking
in Application Networking
06-23-2012
11:45 PM
06-23-2012
11:45 PM
Hey all, I have a customer who has a ace HA pair, the primary ace is shut down, and they've been making changes to the standby ace which has been working ok. They want to bring up the primary ace again, but I just want to confirm the process so I don't overwrite the configuration of the current standby ace when the primary ace is brought back online. I don't have any experience with these boxes yet. But I was thinking about turning preemption off and increases the standby priority to make it the primary? Thoughts? Many thanks. Sent from Cisco Technical Support iPad App
... View more
Labels:
03-19-2012
02:48 AM
Hey All, Are the CSS content switches end of life / support now? I have a customer that is after a design to load balance servers in DMZ off the ASA and servers in Internal Subnet off the ASA. I was going to get Cisco involved but thought they may no longer be support the CSS Thanks in advance.
... View more
Labels:
Created by
alanc3141592654
in Network Security
in Network Security
02-17-2012
09:56 PM
02-17-2012
09:56 PM
Did you get a solution for this?
... View more
02-23-2011
12:47 AM
Hey All, I have a question in regards the fail over link between asa's So, I know cisco suggest using a failover link as fast as your fastest link. But if you have only 2 x 10gb, this seems like a waste of a 10gb. What will happen if we use a 1gb link for a fail over link while we have the 2x 10gb link utilised for other data function? would state information be dropped ? Kind Regards, A
... View more
Labels:
Created by
alanc3141592654
in IP Telephony and Phones
in IP Telephony and Phones
02-06-2011
09:55 PM
02-06-2011
09:55 PM
Hey Guys, I'm wanting to change a incoming number block to another internal range on a h313 gateway. Example Incomming change 12345XXX to 12346XXX then swap it around for out going 123456XXX to 12345XXX Would this be correc for incomming ? Voice translation-rule 1 rule 1 /^12345/ /12346/ I guess for out going the transformations in call manager will sort that Thoughts? cheers, Alan
... View more
Labels:
02-03-2011
04:50 AM
Hey Guys, I've rebooted our publisher v8.0.2, and in the show hardware I get the below. As you can see the state for the 2nd drive is out of sync (OSY) But the state of volume says resyncing... How long does this take? it's been a few hours now? Many Thanks ontroller information ------------------------------------------------------------------------ Controller type : SAS1064E BIOS version : 6.16.00.00 Firmware version : 1.26.81.00 Channel description : 1 Serial Attached SCSI Initiator ID : 112 Maximum physical devices : 62 Concurrent commands supported : 266 Slot : 0 Bus : 1 Device : 0 Function : 0 RAID Support : Yes ------------------------------------------------------------------------ IR Volume information ------------------------------------------------------------------------ IR volume 1 Volume ID : 1 Status of volume : Resyncing (RSY) RAID level : 1 Size (in MB) : 237464 Physical hard disks (Target ID) : 2 3 ------------------------------------------------------------------------ Physical device information ------------------------------------------------------------------------ Initiator at ID #112 Target on ID #2 Device is a Hard disk Enclosure # : 1 Slot # : 1 Target ID : 2 State : Online (ONL) Size (in MB)/(in sectors) : 238475/488397168 Manufacturer : ATA Model Number : WD2502ABYS-23B7A Firmware Revision : 3B04 Serial No : Drive Type : SATA Target on ID #3 Device is a Hard disk Enclosure # : 1 Slot # : 0 Target ID : 3 State : Out of Sync (OSY) Size (in MB)/(in sectors) : 238475/488397168 Manufacturer : ATA Model Number : WD2502ABYS-23B7A Firmware Revision : 3B04 Serial No : Drive Type : SATA ------------------------------------------------------------------------ Enclosure information ------------------------------------------------------------------------ Enclosure# : 1 Logical ID : 5005076b:064c9640 Numslots : 4 StartSlot : 0 Start TargetID : 0 Start Bus : 0 of
... View more
Labels:
Created by
alanc3141592654
in IP Telephony and Phones
in IP Telephony and Phones
12-14-2010
03:56 PM
12-14-2010
03:56 PM
As the previous post stated, this is normally due to the codec used. Codecs will compress standard voice really well, But not so good with music. Try changing the Codec, But you could get a bandwidth hit.
... View more
Created by
alanc3141592654
in Other Collaboration Subjects
in Other Collaboration Subjects
11-18-2010
04:39 PM
11-18-2010
04:39 PM
I believe I installed a day light savings patch from microsoft which corrected the time. Hope this helps
... View more
04-08-2010
08:34 PM
thanks, i've already read through the guide and know the default values. Raising to a larger value, does make it work. But I was just wondering if there is a way to set up a access list or something, so it still works when the printer moves to a new port..? i.e there is a arp access-list for devices with static IPs. Maybe this is not possible. A
... View more
04-08-2010
06:40 PM
Hey All, I've implemented layer 2 security for DAI and DHCP snooping etc I've set the the following interface command for packets per second. "ip arp inspection limit rate 100" But I noticed printers go over the 100 now and then, and the port goes into err-disable. So questions, Is 100 a appropriate value? I've never had any user ports have issues as of yet. Is there a way to make limit rate unlimited for specified mac addresses? as the printers can move around. Many Thanks, Alan
... View more
Labels:
Created by
alanc3141592654
in IP Telephony and Phones
in IP Telephony and Phones
03-10-2010
04:36 PM
03-10-2010
04:36 PM
Hey Guys, looks like an issue with the windows servers ntp... they've yet to fix it, But we pointed the ccm pub at a unix box for NTP and it worked straight away and no more NTP sys logs. So, thank you all for your help
... View more
Created by
alanc3141592654
in IP Telephony and Phones
in IP Telephony and Phones
03-09-2010
03:22 PM
03-09-2010
03:22 PM
thanks for your replies and tips, I will go through these today. 192.168.32.43 is a windows 2003 server, I'm aware windows does not use true NTP, but call manager understands sntp ? Thanks again. A
... View more
Created by
alanc3141592654
in IP Telephony and Phones
in IP Telephony and Phones
03-08-2010
06:07 PM
03-08-2010
06:07 PM
Thanks for your reply... If i check the NTP server from the pub I get 192.168.32.43 The NTP service is accessible. If i check the NTP status from the console of the pub I get admin:utils ntp status ntpd (pid 27280) is running... remote refid st t when poll reach delay offset jitter ============================================================================== 127.127.1.0 127.127.1.0 10 l 42 64 3 0.000 0.000 0.004 192.168.32.43 192.168.32.41 3 u 15 64 3 0.226 -10102. 1.146 unsynchronised time server re-starting polling server every 16 s Current time in UTC is : Tue Mar 9 01:49:06 UTC 2010 Current time in Australia/Brisbane is : Tue Mar 9 11:49:06 EST 2010 So, If the NTP service is accessible? why is it un sychronised? Many Thanks, A
... View more
03-08-2010
03:35 PM
Hey All, I've just started receiving the below messages in the syslog of our publisher call manager 6.1, the clock on the main NTP is correct, what do these mean? should they be appearing in the syslog? Date: Mar 6 08:02:25 Machine Name: xxxxx Severity: Notice Process: ntpd[4516] Message: : time slew 0.000000 s Date: Mar 6 08:02:31 Machine Name: xxx Severity: Notice Process: ntpd[5131] Message: : ntpd 4.1.2@1.892 Tue Feb 24 06:32:25 EST 2004 (1) Date: Mar 6 08:02:31 Machine Name: xxx Severity: Info Process: ntpd[5131] Message: : precision = 9 usec Date: Mar 6 08:02:31 Machine Name: xxx Severity: Notice Process: ntpd[5131] Message: : kernel time discipline status 0040 Date: Mar 6 08:02:31 Machine Name: APPCAMPR01 Severity: Info Process: ntpd[5131] Message: : frequency initialized -15.326 from /etc/ntp/drift
... View more
Labels:
Created by
alanc3141592654
in Application Networking
06-23-2012
06-23-2012
Hey all,I have a customer who has a ace HA pair, the primary ace is shut
down, and they've been maki...
03-19-2012
Hey All,Are the CSS content switches end of life / support now?I have a
customer that is after a des...
02-23-2011
Hey All,I have a question in regards the fail over link between asa'sSo,
I know cisco suggest using ...
02-06-2011
Hey Guys,I'm wanting to change a incoming number block to another
internal range on a h313
gateway.E...
02-03-2011
Hey Guys,I've rebooted our publisher v8.0.2, and in the show hardware I
get the below. As you can se...
Created by
alanc3141592654
in IP Telephony and Phones
12-14-2010
12-14-2010
As the previous post stated, this is normally due to the codec used.
Codecs will compress standard v...
Created by
alanc3141592654
in Other Collaboration Subjects
11-18-2010
11-18-2010
I believe I installed a day light savings patch from microsoft which
corrected the time.Hope this he...
04-08-2010
thanks, i've already read through the guide and know the default
values.Raising to a larger value, d...
04-08-2010
Hey All,I've implemented layer 2 security for DAI and DHCP snooping
etcI've set the the following in...
03-10-2010
Hey Guys,looks like an issue with the windows servers ntp... they've yet
to fix it, But we pointed t...
03-09-2010
thanks for your replies and tips, I will go through these
today.192.168.32.43 is a windows 2003 serv...
03-08-2010
Thanks for your reply...If i check the NTP server from the pub I
get192.168.32.43The NTP service is ...
Public Statistics
| Date Registered | 09-20-2007 08:27 PM |
| Date Last Visited | 05-08-2019 12:01 AM |
| Total Messages Posted | 84 |
| Total Helpful Votes Received | 4 |
