Cisco Community
English
Register
Great changes are coming to Cisco Community in July. LEARN MORE
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Jason Fraioli
‎07-18-2018

Participant
Recent Badges
Awards
Recent Badges
See all
CCP Member
1 Accepted Solution
5 Accepted Solution
10 Helpful Vote
1 Helpful Vote
50 Replies
20 Replies
10 Replies
5 Replies
Stats
Member since ‎08-31-2007
219
Posts
25
Helpful
5
Solutions

Re: Strategy to save sync configs (run->start)

Created by in Network Management
08-09-2010
08-09-2010
2950, 3550, 3750, 6509. I know the 2950 will not be supported and I'm not sure what option I have th...

Re: Strategy to save sync configs (run->start)

Created by in Network Management
08-09-2010
08-09-2010
Collin,Thank you for the prompt and detailed reply. How do TCL scripts work? It appears as though I ...

Strategy to save sync configs (run->start)

Created by in Network Management
08-09-2010
08-09-2010
I posted on this topic some time ago and I can't find the topic. Our helpdesk personnel are tasked w...

Is LMS 3.0 EOS/EOL?

Created by in Network Management
07-22-2010
07-22-2010
I have the following modules installed, all of which are listed as EOS/EOL -> http://www.cisco.com/e...

Re: Subnetting from Flat Network

Created by in Switching
04-08-2010
04-08-2010
Sounds like you are off to a good start."I went out to one my switches (3560) and created a new Vlan...

Re: Cisco View / Save running config

Created by in Network Management
03-11-2010
03-11-2010
Mike, this would work for most of my infrastructure, but I do have some older 2950 switches. I can't...

Cisco View / Save running config

Created by in Network Management
03-11-2010
03-11-2010
Our helpdesk folks use Cisco view to enable/disable ports. Yesterday one of our switches lost power ...

Migrating CW to new server

Created by in Network Management
02-09-2010
02-09-2010
I am looking for documentation on moving a CiscoWorks environment to a new physical server.

Core switch ACL question

Created by in Switching
02-08-2010
02-08-2010
I have a core switch with around 20 vlans connected. I need to be able to do the following:1) Permit...

Re: Not pruning vlans from trunks

Created by in Switching
02-03-2010
02-03-2010
So if you want to restrict vlans on trunks on VTP transparent switches you would need to use the "sw...

Re: Not pruning vlans from trunks

Created by in Switching
02-03-2010
02-03-2010
This is the case if you are operating in VTP client/server mode, but what about transparent mode?

Not pruning vlans from trunks

Created by in Switching
02-03-2010
02-03-2010
Suppose you have two switches (switch a and b) and one router performing the routing. Each of the tw...

CW: Trunk VLANs Mismatch

Created by in Network Management
02-03-2010
02-03-2010
Both switches are configured with the same allowed vlansswitchport trunk allowed vlan 2-4094Can anyo...

STP - high number of topology changes

Created by in Switching
01-15-2010
01-15-2010
RD-CORE-1#sh spanning-tree detail VLAN0010 is executing the rstp compatible Spanning Tree protocol B...

NTP Configuration as of 1 Jan 2010

Created by in Switching
01-07-2010
01-07-2010
For some reason the clocks on some of my switches will not update via NTP. The NTP configuration has...
Public Statistics
Date Registered ‎08-31-2007 06:40 PM
Date Last Visited ‎07-18-2018 12:03 AM
Total Messages Posted 219
Total Helpful Votes Received 25
Helpful Votes Given To
Helpful Votes From