About Grishazahid

Grishazahid · 06-24-2020

Hello everybody!Is there an ability to manage CME via graphical user interface securely?I know about 3 tools but all of them won't help:* CME GUI(sip phones cannot be configured - linkhttps://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/co...

Grishazahid · 06-12-2020

cisco cme ukrtelecom 195.5.0.54Hello everybody!I try to configure SIP trunk without username and password.Situation 1) When I use my white IP on CME g0/0 port - everything is OK, calls are workingSituation 2) When I put CME behind NAT and configure p...

Grishazahid · 05-22-2019

Greetings!Do ASA 5540 has USB flash support? There are two usb ports on back side of ASA. I plug in USB flash and enter the next:ciscoasa# dir disk1:%Error opening disk1:/ (No such device)Firmware file is asa917-29-k8.binThe same USB flash works with...

Grishazahid · 04-03-2019

Hello!Can Anyone help me?I am trying to configure pickup groups on Cisco CME 12.2 (Call Manager Express)First group (№3000) is two grandstream GXP1405 phones and second group (№2019) is cisco phonesAll phones are registered and able to make calls bet...

Grishazahid · 03-04-2019

Hello! Is there any ability to make videocalls between Polycomm Real presense group 310 and Cisco SX80? I have found document on Polycom web-site. https://support.polycom.com/global/documents/support/strategic_partner_solutions/Cisco_Solution_Deploym...

Grishazahid · 06-30-2020

You can specify phone firmware in voice register globalvoice register globalmode cmesource-address 192.168.0.1 port 5060max-dn 5max-pool 5load 7960-7940 P0S3-08-5-00create profileAlso, if your ISR acts as TFTP server, don't forget to specify tftp com...

Grishazahid · 06-24-2020

Hello! If I will be in your situation, I would erase startup config on RT, SW and hard reset phone.And tried to simplify config, left only voice register global, pool, dn, and dial-peer.

Grishazahid · 06-24-2020

I had the same problem when this phone was connected via POE. My switch was not able to provide enough power to Phone+KEM, so only phone boot successfully. Purchasing power cable solved problem

Grishazahid · 06-18-2020

Here is solution for those, who will read this topic in the future: you need to modify sip headersPart of my working config for situation when CME is located behind nat. SIP & RTP ports are forwarded to CME by firewall CME-1#sh run | sec dial-peerdia...

Grishazahid · 06-17-2020

Hurrah its working! :)I created "voice class sip-profile" like in telnyx config guide, applied it to outbound dial-peer and my outgoing calls began to work!Tomorrow I will test incoming dial-peer

Member Since	‎03-05-2018 04:25 AM
Date Last Visited	‎10-19-2023 12:01 AM
Posts	30
Total Helpful Votes Received	5

User Statistics

User Activity

CME web managing

CME & Ukrtelecom 195.5.0.54

ASA 5540 does not see USB flash

Grandtream GXP1405 and Cisco CME Pickup-Groups

SX80 videocalls with Polycomm Real Presence Group 310

Re: CP-7821 not registering

Re: CP-7821 not registering

Re: KEM module disabled by administrator

Re: CME & Ukrtelecom 195.5.0.54

Re: CME & Ukrtelecom 195.5.0.54