About rlaplante@bhfs.com

rlaplante@bhfs.com · 04-13-2017

Why am I asking an ESX question on a Cisco Community. Plain and simple...Cisco and Cisco folks support VMware better than VMware support does. I am also going to risk the whole supported vs. unsupported discussion. My root question> Has anyone upd...

rlaplante@bhfs.com · 02-02-2017

Regarding PnP, are there a downloadable package of plug and play templates for the PnP app in APIC-EM. All of the documentation regarding this app references Prime and that the templates are imbedded in Prime. I'm not seeing default templates like ...

rlaplante@bhfs.com · 08-01-2016

Hello All, Hope your day is going well. I manage a Flexpod environment that was installed roughly 3 years ago. At the time It was 3ea. chassis, 2ea. Nexus 5k, 20ea. B200 M3 blades all running ESXi 5.0, UCS Firmware 2.0 1(c), NetApp FAS etc. We hav...

rlaplante@bhfs.com · 03-16-2016

I am working on a 4 site IWAN - PFRv3 install. This is currently in lab. I thought I had it all working but when I started generating some traffic for testing I found that all traffic paths are using the same tunnel. The domain master exist cli sh...

rlaplante@bhfs.com · 03-07-2016

HI All, I'm working on a PFRv3 / IWAN implementation. It is currently in a lab state. Four sites and each site has dual routers. HUB-R1 is MC / BR (Tunnel /DMVPN 100), HUB-R2 is BR (Tunnel/DMVPN 200). Each of the MC routers on each site all log ...

rlaplante@bhfs.com · 04-14-2017

I use Image Builder /PowerCLI to further customize the the Cisco OEM image. You can remove the old (or too new) drivers and add drivers that match the Cisco firmware you are using. https://pubs.vmware.com/vsphere-50/index.jsp?topic=%2Fcom.vmware.vsp...

rlaplante@bhfs.com · 08-02-2016

I did not know specifically about 2.2(7b). That in itself does not solve the issue for me. Basically I am also stuck on ESXi 5.5 GA. U1 through U2 are documented as being supported by all parties but tickets into TAC for communication issues etc t...

rlaplante@bhfs.com · 03-22-2016

I was so focused on your reply from the other post I didnt see this reply. Reposting the resolution here. The Devil is in the details. Your reply helped me focus and discover the root cause, so thank you very much. I was only seeing RX in the Initi...

rlaplante@bhfs.com · 03-22-2016

The Devil is in the details. Your reply helped me focus and discover the root cause, so thank you very much. I was only seeing RX in the Initial State. TX was Reachable. Not sure how that added up to me checking the routing config but it did. On...

rlaplante@bhfs.com · 03-21-2016

I see in the 'show domain...channels' cmd that all of the tunnels over MPLS2 are provisional state as 'initiated and open' but the operational state is 'not-available' Now to figure out why.

Member Since	‎09-10-2012 10:44 AM
Date Last Visited	‎08-18-2017 03:53 AM
Posts	36
Total Helpful Votes Received	41

User Statistics

User Activity

ESXi Auto Deploy and Image Builder

APIC-EM PnP Templates

Migrating off of VM-FEX

IWAN PFRv3 Load Balancing

PFRv3 DOMAIN-5-TCA System Message

I use Image Builder /PowerCLI

I did not know specifically

I was so focused on your

The Devil is in the details.

I see in the 'show domain..