About j.a.m.e.s

j.a.m.e.s · 04-19-2024

Could someone tell me where is the best place to globalise the called party from the perspective of a phone please?I am migrating to E164 and would like to know if this could be done at the device pool level using transformation patterns.e.g. If a us...

j.a.m.e.s · 04-01-2024

I'm preparing to migrate our CUC from SCCP -> SIP, but I'm struggling to work out how CUC uses the following settings (most are on the SIP Trunk).Inbound Calls CSSRerouting CSSOut-of-Dialog Refer CSSDiversion Header Enabled inbound and outboundCallin...

j.a.m.e.s · 03-26-2024

Can a translation-profile applied on an incoming DP influence the match of an outgoing DP?My use case is a CUCM sending SIP INVITEs with 8 digits in the To field, but I would like to configure the outgoing POTS dial-peers using an E164 destination-pa...

j.a.m.e.s · 03-24-2024

Could anyone advise me please, would a POTS dial-peer which receives an incoming call leg use it's destination-pattern to set the calling party (ANI) for that call? dial-peer voice 100 pots description Lift01 destination-pattern +44123456789$ <-- W...

j.a.m.e.s · 02-28-2024

Could anyone tell me if I would be able to connect a 1G GLC-SX-MMD in Eth1/49-52 for the N9K-C93108TC-FX3P please? I know the QSA is required (CVR-QSFP-SFP10G) to assist with this kind of speed drop.According to the transceiver matrix this should be ...

j.a.m.e.s · 04-17-2024

I'm also confused by what/how to set the AAA timers relevant to the WLC in ISE, but my educated guess is this:1. Policy Elements -> Results -> <YourAuthorizationProfile> -> Common Tasks -> Reauthentication2. Policy Elements -> Results -> <YourAuthori...

j.a.m.e.s · 04-16-2024

There are certain minimum ASA version requirements and flash memory requirements, but I don't think any configuration changes are generally required when going from v4.10 to v5.X.You mentioned using web-deploy, so the equivalent to this config needs ...

j.a.m.e.s · 04-01-2024

Thanks a lot Maren, this is useful info. For the 'Calling Party Selection' does this have some impact on the diversion header itself? I would like to understand at the SIP level what this does if possible.Note: I can see this can be set on the CM tru...

j.a.m.e.s · 04-01-2024

Having read a few more posts I'm piecing this together slowly. Sorry if this raises a few more questions, but to summarise my understanding so far:Inbound CSS: Used when CUC does a "Supervised" call transferRerouting CSS: Used when CUC does a "Releas...

j.a.m.e.s · 03-31-2024

Just a quick shout out to anyone implementing CUBE MultiVRF and using IOS-XE v17.x (that should be most people at the time of writing), there is a bug which prevents calls matching the incoming dial-peer if a SIP message (e.g. Options Ping) arrives d...

Member Since	‎09-07-2002 03:43 PM
Date Last Visited	‎04-24-2024 12:05 AM
Posts	282
Total Helpful Votes Received	154

User Statistics

User Activity

Best way to Normalize/Globaliz Called Number to E164

CUC to CUCM SIP Integration Trunk Settings

VGW Translations and Dial-Peer Selection

How analog POTS dial-peer sets calling party for calls arriving

N9K-C93108TC-FX3P 1G Fibre in the QSFP28 ports

Re: I ended up answering my own

Re: AnyConnect 4.10 upgrade to Secure Client 5.x

Re: CUC to CUCM SIP Integration Trunk Settings

Re: CUC to CUCM SIP Integration Trunk Settings

Re: CUBE MultiVRF Limitations