About Othacon

Othacon · 01-31-2024

Hi everyone,hope you can help with EIGRP unequal load balancing in a Catalyst 3650. I have a system where I need to send the traffic to reach the 10.1.40.0/24 via the vlans 4084 and vlan 4087. Due to the metric, the vlan 4084 as the lowest FD and vla...

Othacon · 08-17-2023

Hi all, i'm having a weird issue that I never saw before. I have two cisco 3650s in a collapsed core configuration, and connected to this switches I have 5 - 2960s that are access switches. I have connected to the two main switches video recording de...

Othacon · 08-01-2023

Hi everyonehope you can help me.I'm having the weirdest of issues where I have two Cisco 3650s-24TS connected to each other via a LAG with 4 x 1 Gbps links and have configured several vlans to do HSRP between them. Besides this two switches, I have a...

Othacon · 01-13-2023

HI all,hope I can have your expertise. I'm currently in the middle of an installation where I'm having a weird issue. We have the following installed The network is bigger than this, but going to start with the basic since this is happening between ...

Othacon · 03-20-2020

Hi all, hope you can help me.I've been hitting with my head trying to put a VPN L2TP with IPsec Policy to work but I haven't been able to.Basically I have a Draytek router (LAN IP 10.14.99.99) connected to a Cisco Router via the Wan 1 port (WAN IP 1...

Othacon · 02-02-2024

Thank you Georg, just executed the show commands and I get this:From the tempelate below, the only thing really that the switch allows me to add is "ip bandwidth-percent eigrp". The rest doesn't allow me to add to the interface. I can add the delay a...

Othacon · 02-02-2024

Well, after reading you post @Joseph W. Doherty , remembered to check if the switches had configured the "qos queue-softmax-multiplier" config. I've applied my policy map to the interface but assumed that this option was already enabled... it wasn't....

Othacon · 02-01-2024

I may be wrong, but I don't think so @MHM Cisco World , because what EIGRP was doing, in essence was this:All the traffic of 6 sites was being funneled to the ASW from CSW 2 and then down a 1Gbps pipe to the Main CSW from the ASW. The Link from CSW1 ...

Othacon · 02-01-2024

@MHM Cisco World at the moment I don't have asymmetric traffic running in the network. I was able to solve all my drops by disabling Vlan 4084. I'm forcing now all the traffic to enter via the right side of the network and the left side. By doing thi...

Othacon · 02-01-2024

Indeed @MHM Cisco World , the issue I have is that when the data from CSW 2 reaches the receiving point it doesn't enter straight in another core, it enters in an ASW at 2Gbps, but then all the traffic is being funneled to the main CSW at 1Gbps. This...

Member Since	‎03-20-2020 10:08 AM
Date Last Visited	‎02-14-2024 12:05 AM
Posts	25
Total Helpful Votes Received	1

User Statistics

User Activity

EIGRP Unequal Load Balance

Computer affecting the Multicast of Other devices

Cisco 3650 - Can't ping SVIs after IOS Upgrade

Symbol Error when reaching the 10Gbps limit of the interface

L2TP over IPSEC Passthrough - Issues

Re: EIGRP Unequal Load Balance

Re: EIGRP Unequal Load Balance

Re: EIGRP Unequal Load Balance

Re: EIGRP Unequal Load Balance

Re: EIGRP Unequal Load Balance