About Alain Cloet

Alain Cloet · 11-22-2011

Dear all,I hope any of you can help me, or give me an idea where to look ...I have a stack of 2 C3750-switches (WS-C3750G-24TS-1U) with IPBASE-firmware (12.2(52)SE). When I ping to a machine (in this case a virtual one), the replies are always recei...

Alain Cloet · 09-05-2011

Hi,As the title says, I can't connect to my stack over Telnet nor via the console cables (serial). When I try to connect via telnet, I just get a time-out.When I try to connect via the Console Cable I get the lines "Switch con0 is now available" / "P...

Alain Cloet · 12-21-2010

Dear,I've been looking through the SW-config guide, some fora, some QOS-best practices, VACL,... but it only confuses me more...In our network, which are mainly all Cisco 3750-range switches, I want to prioritize a specific VLAN, but I can't figure ...

Alain Cloet · 12-04-2009

On a specific VLAN - used for storage - I'd like to enable jumbo frames (9000 bytes).If I check the manual, it states than it's possible to do this on a VLAN (command VLAN MTU 9000), but on the other hand, Jumbo frames need to be configured via SYSTE...

Alain Cloet · 07-22-2009

Hi,With a Cisco 877 Router I want to make a setup in which the outside address is translated when using port forwarding to an the inside address.The port forwarding is working like it should, but I don't know if it's possible to combine this with the...

Alain Cloet · 09-15-2011

I was checking this thread as I have the same questions, which aren't really answered in my opinion...If the memory is ok (I do have to check this for my stack): Is it possible to use the same Base software (c3750e...SE3) for the older C3750G switche...

Alain Cloet · 09-06-2011

Thanks for the info ... could do this yet, as this stack is rather important ; and I can't just turn it off during the week...The good part is it still works, and for the urgent 'change' I repatched to a switch I can connect to...At the moment the s...

Alain Cloet · 01-04-2011

Hi Shashank,Thanks for the reply. It is very clear what I have to do, but it doesn't solve all my doubts . Next to that I prefer to understand what I do, so I can make some interpretation on the possible problems...It does make clear that even if i...

Alain Cloet · 12-11-2009

Yes, I did a reload of the switch, that's how we noticed it didn't work like we wanted . Than I turned off the jumbo frames again, and did a new reload to undo the change...I got info that it should work correctly bases on info given by the storage ...

Alain Cloet · 12-10-2009

I need it for all the servers on the VLAN (as that VLAN is exclusive for storage), with the 3750G-switches it's even impossible to set it port-based.With the current settings (system jumbo at 1500 and storage-VLAN set to 9000) it shows the 9000 for ...

Member Since	‎06-18-2009 11:31 AM
Date Last Visited	‎08-18-2017 03:53 AM
Posts	20

User Statistics

User Activity

C3750: Packets lost

3750: Can't connect to stack (Console Cable / Telnet) - Memory Issue

VLAN Based QOS on 3750

3750(G) / Jumbo frames

877: Port Static NAT with normal Static NAT

Re: Mixed Stack C3750G + C3750X IOS Update

3750: Can't connect to stack (Console Cable / Telnet) - Memory I

Re: VLAN Based QOS on 3750

Re: 3750(G) / Jumbo frames

Re: 3750(G) / Jumbo frames