About josephd2020

josephd2020 · 11-09-2020

Hi, I have created an L2 Switching configuration using L2VPN, Is there a way for me to add VRF and HSRP to this setup? here is my current L2VPN config ======================nterface Bundle-Ether2description mtu 9216!interface Bundle-Ether2.999 l2tran...

josephd2020 · 11-05-2020

Hi, I created a BVI interface but its not coming up RP#show l2vpn bridge-domain detailThu Nov 5 02:46:14.610 UTCLegend: pp = Partially Programmed.Bridge group: vlans, bridge-domain: vlan100, id: 0, state: up, ShgId: 0, MSTi: 0Coupled state: disabledV...

josephd2020 · 11-04-2020

Hi, ----------------------------------------- interface Vlan100 description *** ASR to Switch as a trunk port *** ip vrf forwarding Banana ip address 10.12.8.15 255.255.255.240 standby version 2 standby 28 ip 10.12.8.16 standby 28 preempt standby 28 ...

josephd2020 · 09-30-2020

Hi,Do you configure the same number of VRF instances as well as the required number of subinterfaces if you run VRF lite vs MPLS VPN VRF? If I have to configure multiple VRFS spread across routers geographically apart connected via DWDM will configur...

josephd2020 · 09-22-2020

Hi,Can anyone point me to some references, links, case studies, etc, documents on building a business case for using an MPLS L3 VPN? Currently, low tier ISP uses VRF-lite on POPs connectivity (no backbone). Thank you

josephd2020 · 11-09-2020

Thanks, its working, however, for HSRP. if I shutdown one BVI interface, the standby router also gets deleted. I was assuming the standby router will take over but it doesnt look like it doesWhen both BVI's are up===================================...

josephd2020 · 11-08-2020

HI TKarnani, I have modified my config to the below... Now the Bundle Ethernet and BVI doesnt come up!interface Bundle-Ether2mtu 9216!interface Bundle-Ether2.999 l2transportencapsulation dot1q 100rewrite ingress tag pop 1 symmetric!l2vpnbridge group ...

josephd2020 · 11-05-2020

Hi Tkarnani, I can't add that command on the physical interface since it has sub interfaces, I get the error below when I try it. !!% Subinterface or Layer 2 configuration conflicts with existing configuration, or configuration in this commit: Cannot...

josephd2020 · 11-05-2020

Yeah, I got it to work now, so now I can see BVI is up on both my ASK9k and NCS5500 but I am unable to ping the BVI addresses from one box to the other.. Also, how would I test this that vlan100 is being transported on this link? thanks

josephd2020 · 11-05-2020

I just have this interface TenGigE0/0/0/1.100 l2transportencapsulation dot1q 100rewrite ingress tag pop 1 symmetric

Member Since	‎09-08-2020 11:45 PM
Date Last Visited	‎11-13-2020 12:03 AM
Posts	13

User Statistics

User Activity

Configuring HSRP and VRF in EVC model L2VPN XR

BVI interface not coming up

Vlan configuration on ASR9K XR

VRF configuration vs VRF lite

Building a business case for low tier ISP to use MPLS L3 VPN

Re: Configuring HSRP and VRF in EVC model L2VPN XR

Re: BVI interface not coming up

Re: BVI interface not coming up

Re: BVI interface not coming up

Re: BVI interface not coming up