About dkhouri

dkhouri · 01-19-2011

Hi,I seem to be stuck understanding the results on the lab im working on. If you look at the image, i have redistribution configured on R2 and R3 (redistributing EIGRP and OSPF in both directions) and i have RIP being redistributed by R5 into the EIG...

dkhouri · 01-12-2011

Hi all,I have 3 routers running OSPF (R1,R2 and R4. Picture R4 as a hub in a hub and spoke diagram). R4 is an ASBR which is connected to another router (R3), and is running EIGRP between itself and R3. On R4, i have configured route redistribution bo...

dkhouri · 11-08-2010

Hi,I can't seem to find meaningful information regarding the Stub Network state in a Type 1 LSA.E.g Link connected to: another Router (point-to-point) (Link ID) Neighboring Router ID: 1.1.1.1 (Link Data) Router Interface address: 10.45.13.2...

dkhouri · 10-17-2010

Hi,Been pulling my hair out on this one!! OK in my lab environment I have a hub (R1) & spoke (R2 and R3) network with a frame relay switch (R6). For some reason, I am seeing CISCO, status deleted on the spoke routers. This is not allowing me to PIN...

dkhouri · 09-29-2010

Hi,I have built a 3750 switch stack (8 switches) and every now and then (random) when i do a "show run" or "write mem", i get the following error messageNVRAM: Unable to read configuration. Try againIt doesn't happen all the time, its a random thing....

dkhouri · 01-19-2011

Hi Jonathan,I cleared the IP routing table and ospf process on both R2 and R3 and it swoped the paths around. Now R2 takes the path through EIGRP and R3 now goes backwards through OSPF.I even deleted all redistribution configurations on R2 and R3, re...

dkhouri · 01-13-2011

jgraafmansThank you for the info,. I changed the router-id on R3 and can now see all the external routes. I haven't had time to read the link you posted in your reply, but I most definately will.Thanks to the others for their input. Much appreciated....

dkhouri · 01-12-2011

Hi Rob,I only see the OSPF routes on R4's EIGRP topology table. R3 is only showing connected and the single 4.4.4.0/24 network which I purposely advertised to make sure EIGRP was working between R3 and R4.

dkhouri · 01-12-2011

Leo,I have removed the route-map but this didnt help. The route-map has nothing to do with EIGRP. The route-map is used under the OSPF process for the sole purpose of redistribution into OSPF from another routing protocol, which I know is working bec...

dkhouri · 01-12-2011

Hi Leo,Im advertising the below loopbacks into OSPF from R1. These are in area 1. I can see these at inter-area routes on R4. If they are seen by R4 as OSPF routes, then shouldnt they be redistrubting into EIGRP as per the redistribution command unde...

Member Since	‎05-05-2010 04:47 PM
Date Last Visited	‎08-18-2017 03:54 AM
Posts	17
Total Helpful Votes Received	1

User Statistics

User Activity

Route Redistribution - Route Issue

OSFP to EIGRP redistribution not working

OSPF LSA Type 1 - Stub Network

Frame-relay PVC Issue - CISCO, status deleted

NVRAM: Unable to read configuration. Try again later.

Re: Route Redistribution - Route Issue

Re: OSFP to EIGRP redistribution not working

Re: OSFP to EIGRP redistribution not working

Re: OSFP to EIGRP redistribution not working

Re: OSFP to EIGRP redistribution not working